Shop Floor Talk  

Go Back   Shop Floor Talk > Welding and Metalworking Forums > Welding

SFT Search:   
Reply
 
Thread Tools Display Modes
  #1  
Old 07-30-2022, 12:15 PM
camdigger's Avatar
camdigger camdigger is offline
Roving Reporter
 
Join Date: Aug 2008
Location: Central Oilberta
Posts: 4,181
Default Flame straightening

This is one of the best presentations I've seen on the how's and whys of flame straightening. Most interesting to me is a brief reference to applying it to Aluminum sheet metal

A few years ago, there was a collision with a steel framed overpass bridge near here. They brought in a specialized crew and straightened out most of the damage while only shutting down one lane of the 4 lane underneath and one on the 2 lane road on top. Took nearly a month, but they got it all done in situ.

https://youtu.be/IxzV9VeUpLY
__________________
Design to 0.001", measure to 1/32", cut with an axe, grind to fit..
Reply With Quote
  #2  
Old 07-30-2022, 02:27 PM
Whitetrash's Avatar
Whitetrash Whitetrash is offline
Elite Member
 
Join Date: Mar 2009
Location: Estes Park, CO [Around 8000 Ft. Elv.]
Posts: 4,252
Default

When I was at the fab shop we built a custom size I-Beam for a steel mill crane run. The top and bottom flanges were bowed and had to be straightened before they could tacked up and welded. Two of the Old Hands worked with one of the big rosebuds with the head the size of a popcan and a stringline brought them into spec. It was pretty cool to watch.
__________________
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
Reply With Quote
  #3  
Old 08-02-2022, 02:37 AM
Lowe.Buuck Lowe.Buuck is offline
Junior Member
 
Join Date: Jul 2017
Location: Minnesota, USA
Posts: 39
Default

I got interested in this topic a few years back. Not a lot of information online about the specifics.

The "Bible" on the topic is Flame Straightening Technology for Welders by John P. Stewart. 106 pages describing 36 processes with illustrations.

Welding Fabrication & Repair by Frank M. Marlow, P.E. has some information and illustrations on Flame Straightening in Chapter 4, Bending & Straightening.

Fundamentals of Flame Straightening (32 pages) is available as a PDF from Linde and BOC.

Removal of Out-Of-Plane Distortion in Mild Steel Panels Using Flame Heating by Larry Lee Janca at MIT. 164 page PDF.

One important thing to note is it takes a lot of heat. If you plan on using a large OA rosebud make sure you pay attention to the acetylene withdraw rate on your tank. You can only remove 1/7 of the tank volume per hour. If you withdraw more than that you will also remove some of the acetone from the tank.

I have a 150,000 btu OA rosebud. On a 150 cuft tank you can only use it 9 minutes per hour.

You may want to look at rosebud tips designed for oxy-propane. The tanks only contain propane and the only limitation is the rate that liquid propane converts to vapor. You need one 100# tank per 100,000 btu of torch capacity. Small BBQ tanks don't provide enough space for the liquid propane to convert to vapor fast enough to supply large rosebud tips.

You can plumb multiple propane together to supply larger tips.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Web Search:

All times are GMT -5. The time now is 11:23 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.