|
#1
|
||||
|
||||
Asking for brand opinions on struts.
I need to replace the front struts on my 2011 Ford Explorer again.
My question is what brand would you guys/gals use on your personal vehicle. Attached is a picture of the ones that fit my car, which is AWD. I don't mind spending money on a better product. But I can tell you that the Motorcraft brand is not anything special. But are the KYB, Gabriel or Monroe's worth the extra cash, or are they all basically the same.
__________________
Shade "Prepare to defend yourselves." -- Sergeant Major Basil L. Plumley, Ia Drang Valley |
#2
|
||||
|
||||
https://bilstein.com/en-us/products/
I think PartsGeeks had decent pricing on these... PS: I wouldn't buy "loaded" struts (ie: with springs) as their one-size-fits-all spring rates may be different than stock. Maybe if I had sagging springs... But DO get new dust covers, bearings and bumpers
__________________
TA Arcmaster 185 w/tig/stick kit MillerMatic 252 w/3rd gen 30A MM140 w/o AS, w/CO2 Hobart (Miller) 625 plasma Hobart 250ci plasma Victor O/A (always ready, but bored) HF 80 lunchbox w/tig 45ACP Black Talons for those stubborn jobs... |
#3
|
||||
|
||||
Personally I would go with Monroes or Gabrils. I have had both brands on compact cars, full sized cars and half ton trucks and was satisfied with both brands service and price wise. I have no experience with bilstein but have heard rumours that they are more hype than help unless in a race or performance application. YMMV.
__________________
I love the smell of napalm in the morning. It smells like, victory! Rommel, you magnificent bastard, I read your book! Still got the shovel! Victor Torch Set With Meco Regs Lincoln Weld Pak 100 Giant Tech Arc 200 Miller Roughneck2E |
#4
|
||||
|
||||
Quote:
work swapping springs. and I am going to assume if they say the part fits the spring constant is correct. But damn they are proud of their products. I have the tools to do it, and have, but I can afford a few extra bucks. The Exploder is easy, jack it up, take off the wheel. 3 bolts in the wheel well and 4 up top and swap the old for the new. Torque everything up and have my tire guy do the alignment. I have Bilsteins on the front of my F-350, they seem fine and they were priced close to other brands at the time. Quote:
bought, nothing urgent but I can tell I will need to replace them before the summer is out. I like heading into winter with the cars and trucks at 100%.
__________________
Shade "Prepare to defend yourselves." -- Sergeant Major Basil L. Plumley, Ia Drang Valley |
#5
|
||||
|
||||
know nothing of gabriel but I'd rank bilstein a clear first, then monroe, then kyb.
|
#6
|
||||
|
||||
Decades ago I purchased Monroe from PEP-Boys, rear shocks not struts.
Monroe's started leaking about 5 years later, life-time warranty gave me Gabriel replacements and still good. Just a note, you should check the rod diameter I heard in general Gabriel may be larger than others or stock which I assume are better.
__________________
* * The factory of the future will have only two employees, a man and a dog. The man will be there to feed the dog. The dog will be there to keep the man from touching the equipment. ~Warren G. Bennis |
#7
|
||||
|
||||
Short answer is Yes. They are worth the extra money, unless your time is worthless. I am a fan of Gabriel or Monroe, either one is good.
__________________
Gerry You got freedom of speech, if you don't say too much. Aaron Neville. When a liberal screams racism, you can bet they were also born with white skin. Common sense is like deodorant. The people that need it most never use it. Joe Concha |
#8
|
||||
|
||||
I put the loaded struts from Detroit Axle on my 2011 Silverado a couple years ago. I bought them from Amazon. I have used Detroit Axle pads and rotors on 4 different vehicles with no issues.
I don't know where they rank on quality but from what I have used I am satisfied.
__________________
Curator of the canned cycles. I'm a man, but I can change, if I have to, I guess.--Red Green Home is where the G91G28X0Y0 is. |
#9
|
||||
|
||||
Not sure with struts, but my old man taught me to always bleed shocks before installing them.
Sent from my iPhone using Tapatalk |
#10
|
||||
|
||||
I can't find the stuff I used on the Honda Element years ago, but it was a package deal off either Amazon or Ebay--similar to the Detroit Axle deal mentioned. It came with the loaded struts, as well as all new hardware and body bushings and was 'rated' for the vehicle. Looked sorta boring and generic but the price was great and it has performed well.
I've never had much luck when it comes to trying to upgrade shocks and struts through the years. I've spent way more money on things that were supposed to be better that just weren't. I feel like the fancy paint jobs and marketing are just that. The OEMs install mass produced crap designed to just last the length of the warranty anyway. |
Thread Tools | |
Display Modes | |
|
|