Shop Floor Talk  

Go Back   Shop Floor Talk > Welding and Metalworking Forums > Fabrication

 
 
SFT Search:
Reply
 
Thread Tools Display Modes
  #11  
Old 12-13-2013, 04:35 PM
FabberMcGee FabberMcGee is offline
Senior Member
 
Join Date: Mar 2011
Location: Fairbanks, Alaska
Posts: 809
Default

You need a Greenlee brand DB-9S chassis punch. It's considerably over the price your budget is looking for, but as a non-profit and at the end of the year you might be able to do some arm twisting and get one donated. While I was searching I see rmack found them at a better price than the Greenlee.

Good luck.

https://www.google.com/#q=Greenlee+DB-9S
__________________
"The trouble with having an open mind, of course, is that people will insist on coming along and trying to put things in it."

“The thing about quotes on the internet is you cannot confirm their validity” Abraham Lincoln
Reply With Quote
  #12  
Old 12-13-2013, 04:46 PM
USMCPOP's Avatar
USMCPOP USMCPOP is offline
Gold Star Dad
 
Join Date: Jul 2006
Location: Richmond, VA area
Posts: 12,374
Default

Those panel punches are expensive but professional. If you get one, be sure it is the correct one. Many refer to these as "DB" connectors, but they're "D connectors" with different letters/numbers.

I have punched small holes in thin steel using nothing more than a sharp, flat-faced pin punch. Trick is to put the sheet on a piece of end-grain scrap wood. A hard whack with the hammer deforms the wood and drives the slug into it. It's a whole lot easier to make a 1/4" hole this way than drilling thin sheet metal.
Attached Thumbnails
Click image for larger version

Name:	DSubminiatures-connector-sizes-Dsub-naming.png
Views:	1427
Size:	38.4 KB
ID:	111983  
__________________
USMCPOP

Last edited by USMCPOP; 12-13-2013 at 04:53 PM.
Reply With Quote
  #13  
Old 12-13-2013, 04:54 PM
GWIZ's Avatar
GWIZ GWIZ is offline
SFT Historian
 
Join Date: Feb 2006
Location: USA
Posts: 7,615
Default

Everyone should have one.
Not production but this one works good, if you want rounded corners then drill the corners first.
http://www.ebay.com/itm/NIB-Original...#ht_252wt_1081



Quote:
Screw-down: Not invented? I've heard of a punch that you just tighten until it punches thru, but have not found any. i imagine drilling a small round hole in my aluminum sheet, then fitting two small separate hardwares on either side of the sheet, screwed to each other through the small round hole. They are some kind of punch and die. Then, tighten them down, and out pops the square hole in my sheet. Does this exist? If not, let's invent it!
"DB15 chassis punch" they are not cheap, looks like the price went down.
http://www.l-com.com/d-sub-punch-db1...e-greenlee-231
__________________
*
*
The factory of the future will have only two employees, a man and a dog. The man will be there to feed the dog. The dog will be there to keep the man from touching the equipment. ~Warren G. Bennis
Reply With Quote
  #14  
Old 12-13-2013, 05:09 PM
johnyradio johnyradio is offline
Member
 
Join Date: Dec 2013
Location: San Francisco
Posts: 55
Default

Quote:
Originally Posted by USMCPOP View Post
Those panel punches are expensive but professional. If you get one, be sure it is the correct one. Many refer to these as "DB" connectors, but they're "D connectors" with different letters/numbers.
Glad i clicked reply, because i could not see your 2nd paragraph! something wrong with this forum

The part i'm using has 3-rows, which is not shown in your pic. I thought it's called DB-15, but you may be correct. Aka D-sub 15. Even McMaster-Carr calls them "DB", and they make special punches just for it. $200! Hoping for a less-expensive option.
http://www.mcmaster.com/#knockout-punches/=pslrz1

Quote:
I have punched small holes in thin steel using nothing more than a sharp, flat-faced pin punch. Trick is to put the sheet on a piece of end-grain scrap wood. A hard whack with the hammer deforms the wood and drives the slug into it. It's a whole lot easier to make a 1/4" hole this way than drilling thin sheet metal.
Thanks for that, it will help when trying to make small holes. Can you link me to a "flat-faced" pin-punch? I cannot find that. (Did you mean it as a solution for my D-sub, or just a friendly side tip?)
Reply With Quote
  #15  
Old 12-13-2013, 05:36 PM
USMCPOP's Avatar
USMCPOP USMCPOP is offline
Gold Star Dad
 
Join Date: Jul 2006
Location: Richmond, VA area
Posts: 12,374
Default

Sorry, Johnny, I edited my post later to add the punch comment. You might be able to make a square-ish punch that will do the job, but you'd have to whack it pretty hard.

I guess you have a DE-15 VGA connector.

These are pin punches.
Attached Thumbnails
Click image for larger version

Name:	9f9d326d-2376-4619-a704-2c6df15a5c1d_400.jpg
Views:	1052
Size:	8.8 KB
ID:	111994  
__________________
USMCPOP
Reply With Quote
  #16  
Old 12-13-2013, 06:16 PM
Ironman's Avatar
Ironman Ironman is offline
Iron Modification Investigator
 
Join Date: Feb 2008
Location: Warburg, Alberta
Posts: 17,505
Default

Quote:
Originally Posted by johnyradio View Post
how does one make a square hole punch? i was wondering if that was possible...
Take a piece of 3/8" square stock, and scribe an X on the end from corner to corner. Then center punch the X.
Take a 3/16" drill and drill a pilot hole straight down the center for 1/2" or so.
Now take a 9/16" drill and carefully drill into the pilot hole far enough that the corners of the3 square stock are sharp edges.
Done.

You can use mild steel, but cold rolled is better and I would not worry about hardening it.
When you need to sharpen, touch it up with a 9/16 drill bit.
You can get fancy and make a squre hole for a female die, and mount a pin in it. That way you can drill a pilot hole in the sheet metal and put the pin through, and using the center hole in the punch be guided into the square die hole, but I would say piss on it and punch through into a piece of end grain firewood.
__________________
Gerry
You got freedom of speech, if you don't say too much.
Aaron Neville.

When a liberal screams racism, you can bet they were also born with white skin.

Common sense is like deodorant. The people that need it most never use it. Joe Concha
Reply With Quote
  #17  
Old 12-13-2013, 06:39 PM
johnyradio johnyradio is offline
Member
 
Join Date: Dec 2013
Location: San Francisco
Posts: 55
Default

Quote:
Originally Posted by Ironman View Post
Take a piece of 3/8" square stock....
wow, amazing tute!!!!
this might just be our option.
what equipment do you recommend for drilling?
if that's all there is to it, why do they cost so much money to buy?
can you think of a way to achieve a rectangular punch?

THANKS!

Last edited by johnyradio; 12-13-2013 at 07:01 PM.
Reply With Quote
  #18  
Old 12-13-2013, 09:15 PM
Gadgeteer's Avatar
Gadgeteer Gadgeteer is offline
Elite Member
 
Join Date: Aug 2006
Location: Southern Montana
Posts: 2,154
Default

Is the hole in the flat, bottom (top) of the plate, or in the curved side of the plate?
Reply With Quote
  #19  
Old 12-13-2013, 09:27 PM
johnyradio johnyradio is offline
Member
 
Join Date: Dec 2013
Location: San Francisco
Posts: 55
Default

Quote:
Originally Posted by Gadgeteer View Post
Is the hole in the flat, bottom (top) of the plate, or in the curved side of the plate?
on the flat
Reply With Quote
  #20  
Old 12-13-2013, 09:38 PM
Scrapper Greg's Avatar
Scrapper Greg Scrapper Greg is offline
7-26-1965 to 6-5-2022
 
Join Date: May 2011
Location: WV
Posts: 4,038
Default

One other question that comes to mind. can you remove the nuts and pull the metal shield off? If so, you could clamp that end cap in between the main body and the metal shield. Would take a bit of the tedium out of this. I too would talk to a few of the companies mentioned. You are a non profit, tax year is coming to an end. Companies are always looking for that last bit of corporate savings.
__________________
MAGA
Reply With Quote
Reply

Tags
aluminum, cut, drill, punch, sheet

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Web Search:

All times are GMT -5. The time now is 06:46 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.