Shop Floor Talk  

Go Back   Shop Floor Talk > Welding and Metalworking Forums > Fabrication

SFT Search:   
Reply
 
Thread Tools Display Modes
  #11  
Old 07-31-2019, 11:17 AM
platypus20's Avatar
platypus20 platypus20 is offline
Boiler God
 
Join Date: Aug 2007
Location: camillus, ny (syracuse)
Posts: 9,592
Default

The lower number of joints has been a true benefit, I’ve cut down about 95% of the leaks I had, I gone from the air compressor cycling once an hour to about 3-4 cycles per day. Most of my loss now is down to the auto-drain blowing for 2-3 seconds every hour.
__________________
jack
Reply With Quote
  #12  
Old 08-04-2019, 09:13 PM
platypus20's Avatar
platypus20 platypus20 is offline
Boiler God
 
Join Date: Aug 2007
Location: camillus, ny (syracuse)
Posts: 9,592
Default

Today, I switched from 1/4” style A Milton air fittings to 3/8” style T Milton air line fittings, which according to Milton, the style and size increase, will give me roughly 3-4 times the flow. With the new bigger air lines and the new air line fittings, air flow should not be a problem.

I checked, I made a mistake, mine are actually Tru-Flate/Amflo T style air fittings (Milton H style) according to them, they are in the 67 cfm range, again I bought what was local, I did not see any V style. All I really know is the air at the end of the hose appears to be about double of what it use to be.
__________________
jack

Last edited by platypus20; 08-05-2019 at 03:01 PM.
Reply With Quote
  #13  
Old 08-08-2019, 08:49 PM
platypus20's Avatar
platypus20 platypus20 is offline
Boiler God
 
Join Date: Aug 2007
Location: camillus, ny (syracuse)
Posts: 9,592
Default

Spent more time today changing from the Milton A style air line fittings to the larger, higher flow Milton H style air line fittings. Damn!! This is getting expensive.
__________________
jack
Reply With Quote
  #14  
Old 08-08-2019, 09:42 PM
greywynd's Avatar
greywynd greywynd is offline
I can dig it
 
Join Date: Dec 2005
Location: Wainwright, Alberta
Posts: 4,716
Default

I noticed a spike in Milton stock recently...


Sent from my iPhone using ShopFloorTalk mobile app
Reply With Quote
  #15  
Old 08-09-2019, 05:19 PM
Whitetrash's Avatar
Whitetrash Whitetrash is offline
Elite Member
 
Join Date: Mar 2009
Location: Estes Park, CO [Around 8000 Ft. Elv.]
Posts: 2,811
Default

67 CFM ought to be able to run a gnarly 1" impact gun and a big DA sander simultaneously
__________________
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
Reply With Quote
  #16  
Old 08-09-2019, 07:05 PM
platypus20's Avatar
platypus20 platypus20 is offline
Boiler God
 
Join Date: Aug 2007
Location: camillus, ny (syracuse)
Posts: 9,592
Default

Now if I had an air compressor, that was capable of 67 cfm!!


Both the 3/4” drive impact guns now have a very noticeably louder bark, than they did before.

I now have a mixed assortment of air fittings on some of the tools. All of the air drops, air lines and hose reels have been changed over to the larger fittings, along with the 3/4” and 1/2” impacts. I have 8” long whips that have the larger input fittings and the smaller outlet fittings, allowing me to use the die grinders and other smaller tools, that don’t use a lot of air. The only smaller fittings is at the tool inlet, eventually I will probably switch over. The thought of changing the 120+ smaller air nipples on the tools, all at once, before SFT members have time to buy Milton stock, to enjoy the income surge, is unthinkable. So buy now!! Now Damn It!!.
__________________
jack

Last edited by platypus20; 08-09-2019 at 07:23 PM.
Reply With Quote
  #17  
Old 08-10-2019, 03:06 PM
mccutter's Avatar
mccutter mccutter is offline
Post Fiend
 
Join Date: Mar 2006
Location: Central Florida
Posts: 8,416
Default

Is this anything that interests you, Jack? Surplus... Hiding somewhere but I'm sure I can find them.
Attached Thumbnails
Click image for larger version

Name:	airfit1.jpg
Views:	50
Size:	197.1 KB
ID:	151750  
__________________

TA Arcmaster 185 w/tig/stick kit
MillerMatic 252 w/3rd gen 30A
MM140 w/o AS, w/CO2
Hobart (Miller) 625 plasma
Hobart 250ci plasma
Victor O/A (always ready, but bored)
Lincoln Patriot autodark (freebie)
45ACP Black Talons for those stubborn jobs...
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Web Search:

All times are GMT -5. The time now is 04:34 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.