|
|
#51
12-14-2021, 08:53 PM
|
||||
|
||||
Quote:
You bought CEE swag! Lol. Sent from my iPhone using Tapatalk
__________________
Brian You don't know what you don't know.  "It's what you learn after you know it all that counts." John Wooden 
|
|
#52
12-15-2021, 05:55 AM
|
||||
|
||||
|
Quote:
__________________
* * The factory of the future will have only two employees, a man and a dog. The man will be there to feed the dog. The dog will be there to keep the man from touching the equipment. ~Warren G. Bennis
|
|
#53
12-15-2021, 06:18 AM
|
||||
|
||||
|
Thinking out loud ......
One option maybe a MT3 socket (or whatever they call them) with a straight shank. plug welded in. what I'm not sure is how hard the surface needs to be I'm thinking case hard. so if you make a new spindle it will likely need to be hardened. some of these sockets maybe hardened but it maybe hit or miss. on the other hand if your old spindle ID is hard lathe tools may not cut it.
__________________
* * The factory of the future will have only two employees, a man and a dog. The man will be there to feed the dog. The dog will be there to keep the man from touching the equipment. ~Warren G. Bennis Last edited by GWIZ; 12-15-2021 at 06:25 AM.
|
|
#54
12-15-2021, 06:52 AM
|
||||
|
||||
|
Quote:
I’m confused. There is no 1.310 on the Morse taper chart. Was it 1.2310 that you was measuring for MT#4? Missed the 2? Probably phone keyboard error? Sent from my iPhone using Tapatalk
__________________
Brian You don't know what you don't know. "It's what you learn after you know it all that counts." John Wooden
|
|
#55
12-16-2021, 10:05 PM
|
||||
|
||||
|
Quote:
No case hardening on the spindle. Both the socket and outer surface cut easily with a file.
__________________
Tim Self appointed director of junk, and old vehicles.
|
|
#56
12-18-2021, 12:18 PM
|
||||
|
||||
|
Chart shows dimension ‘A’ as 1.231”.
What’s the outside diameter of the section with the morse taper in it? I’d be tempted to bore it out, then press in a ‘socket’ with a #3 or #4 taper in it. It would be cheap enough to buy and cut up a socket to use, avoids having to remake the entire piece, and will keep you reasonable ‘stock’ if that’s what you’re after. Heck if you cut the socket off just at the slot for the drift your bore wouldn’t be as deep, and you won’t even have to line that up with the original when you press it in. Sent from my iPhone using Tapatalk
|
|
#57
12-18-2021, 07:52 PM
|
||||
|
||||
|
Been a full day on the road today.
__________________
Tim Self appointed director of junk, and old vehicles.
|
|
#58
12-18-2021, 08:33 PM
|
||||
|
||||
|
So where is the drilling head for that big radial arm drill press. I have one about that size at work. I think I’ve used it 8 times in the last four years.
 Sent from my iPhone using Tapatalk
__________________
Brian You don't know what you don't know. "It's what you learn after you know it all that counts." John Wooden
|
|
#59
12-18-2021, 09:39 PM
|
||||
|
||||
|
Quote:
__________________
Tim Self appointed director of junk, and old vehicles.
|
|
#60
12-19-2021, 04:49 PM
|
||||
|
||||
|
Machines unloaded and safely on the ground.
__________________
Tim Self appointed director of junk, and old vehicles.
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
