Shop Floor Talk  

Go Back   Shop Floor Talk > Welding and Metalworking Forums > Welding

SFT Search:   
Reply
 
Thread Tools Display Modes
  #21  
Old 12-04-2019, 11:49 AM
platypus20's Avatar
platypus20 platypus20 is offline
Boiler God
 
Join Date: Aug 2007
Location: camillus, ny (syracuse)
Posts: 9,650
Default

My God they are expensive............!!

My Powcon experience is terrible, I’d NEVER buy another one, I think I still have a couple dead bodies somewhere.
__________________
jack
Reply With Quote
  #22  
Old 12-04-2019, 01:08 PM
digger doug's Avatar
digger doug digger doug is offline
Not to be used as a Flotation Device
 
Join Date: Jan 2008
Location: NW Pa
Posts: 11,862
Default

Quote:
Originally Posted by platypus20 View Post
My God they are expensive............!!

My Powcon experience is terrible, I’d NEVER buy another one, I think I still have a couple dead bodies somewhere.
Please...Please !

don't tease us like this...inquiring minds want to know...or "How the welder burns"....
Reply With Quote
  #23  
Old 12-04-2019, 08:34 PM
platypus20's Avatar
platypus20 platypus20 is offline
Boiler God
 
Join Date: Aug 2007
Location: camillus, ny (syracuse)
Posts: 9,650
Default

Per DD’s request...

My Powcon Saga.......

Powcon #1 - the output capacitors had failed, they installed new ones, ran on a load tester, worked perfectly. At pick up, plugged it in, flicked the switch, BANG, the output capacitors failed. Two days later, repaired, tested and rechecked by me, okay. Two days later plugged it in, flicked the switch, a loud whistling sound, then BANG, output capacitors failed. The repair shop kept the unit for another 3 months, trying to fix it, finally Powcon took the unit, they sent it back, allegedly repaired, it failed again within 2-3hours of operation. I finally gave up on Powcon #1. Sets in the trunk of my 69 Ramber American.

Powcon #2 - for about 2-3 yrs it was like a Bic pen (first time, every time), then there were issues with the unit shutting itself off, if it went idle for 3-4 minutes. I sent it in, they allegedly fixed the issue, then wild amp swings, while under operation, no penetration to burn through, back to no penetration, then said it was some rheostat issue, a couple hundred dollars, about a day later some kind of power transistor issue, they replaced numerous parts, within a week, same issue, they replaced the parts again, it lasted about 5 hrs, then the flames shot out the back, then finally the big BANG. Gave up on Powcon #2, I believe it’s sets next to Powcon #1.

Powcon #3 - yes, at times I’m a slow learner, compared to the other Powcons, this was the ugly sister, I believe every part except the case, was changed at least once or twice, Powcon had it 4-5 times, still a serious flawed piece, when it worked, it was excellent, it was probably a good concept, but poorly designed/manufactured welder. Finally, the LWS gave me the full purchase price toward a Lincoln Invertec V-300.

The Lincoln Invertec V-300 (one of Lincoln’s first inverter based welders), which worked perfectly, but had roughly a 45 minute procure to change input voltage, no really meant to be changed constantly. Also had a very high amp draw, making it a pain to hook up on the job. About 3-4 years later, I traded the V-300 toward a Lincoln Invertec V-350 Pro (still have it).

Then I went through a series of smaller (200 amp) inverter welders, ESABs, Thermal Arcs, Lincolns, Fornious (sp) and finally Millers, which seem better geared to the type of work we do.

Even mentioning the Powcon name, will probably cause me nightmares.
__________________
jack
Reply With Quote
  #24  
Old 12-05-2019, 07:20 AM
digger doug's Avatar
digger doug digger doug is offline
Not to be used as a Flotation Device
 
Join Date: Jan 2008
Location: NW Pa
Posts: 11,862
Default

Mckeanmachinery had a pair of the larger 600 amp units (and with all the bells, STM & pulse options)

Someone came in and bought them both up.

I picked up 2 of the 300 amp stick units ($200 each) and the amp draw is less than my dialarc (remote barn application with limited power).

But I don't like D.C. with the arc blow, prefer A.C.

I noticed one units ticks like a time bomb when turned on, other does not.

And yes that whistle arc...doo the other inverters doo that ?
Reply With Quote
  #25  
Old 12-05-2019, 11:02 AM
Ironman's Avatar
Ironman Ironman is offline
Iron Modification Investigator
 
Join Date: Feb 2008
Location: Warburg, Alberta, Canada
Posts: 13,969
Default

Quote:
Originally Posted by digger doug View Post

And yes that whistle arc...doo the other inverters doo that ?
When a capacitor of that size fails it heats, building gas pressure from the insulating fluid vaporizing. Escaping vapor whistles. I have heard Hibay lights do the same thing just before the darkness.
__________________
Gerry
You got freedom of speech, if you don't say too much.
Aaron Neville.

The virtue is always a cover for the sin. That's the key to understanding the modern left. Whatever they're accusing you of doing, they are doing themselves but more enthusiastically. And that's definitely the story of Justin Trudeau. Tucker Carlson
Reply With Quote
  #26  
Old 12-05-2019, 11:05 AM
digger doug's Avatar
digger doug digger doug is offline
Not to be used as a Flotation Device
 
Join Date: Jan 2008
Location: NW Pa
Posts: 11,862
Default

Quote:
Originally Posted by Ironman View Post
When a capacitor of that size fails it heats, building gas pressure from the insulating fluid vaporizing. Escaping vapor whistles. I have heard Hibay lights do the same thing just before the darkness.
No, this is normal operation, the arc itself has a whistle.
Reply With Quote
  #27  
Old 12-05-2019, 03:15 PM
toprecycler's Avatar
toprecycler toprecycler is offline
Elite Member
 
Join Date: Jan 2009
Location: Petoskey, Michigan
Posts: 4,123
Default

Quote:
Originally Posted by digger doug View Post
No, this is normal operation, the arc itself has a whistle.


I remember someone saying it was like a Star Wars laser gun sound. After I heard that description, now that is what I hear when I use my powcon.


Sent from my iPhone using ShopFloorTalk
__________________
Brian

You don't know what you don't know.

"It's what you learn after you know it all that counts." John Wooden
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Web Search:

All times are GMT -5. The time now is 01:46 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.