Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 15 of 15
Search took 0.01 seconds.
Search: Posts Made By: OHT
Forum: Welding 09-17-2011, 05:22 PM
Replies: 27
Views: 22,927
Posted By OHT
The "Common Misconceptions" section I found...

The "Common Misconceptions" section I found interesting.

http://www.weldingandgasestoday.org/index.php/2011/07/alternative-fuels/
Forum: Machining 10-17-2010, 10:21 PM
Replies: 11
Views: 2,759
Posted By OHT
JAWCO Tools makes great rethreading dies for the...

JAWCO Tools makes great rethreading dies for the money. There the same size as standard hex nuts. They also have some real odd ball retheading dies, extra fine and LH (very reasonable price).
...
Forum: Fabrication 04-15-2010, 09:50 AM
Replies: 6
Views: 1,917
Posted By OHT
Randy Just in case you didn't notice. There...

Randy

Just in case you didn't notice. There are some more back one page (2935).

Richard
Forum: Fabrication 04-14-2010, 09:54 PM
Replies: 6
Views: 1,917
Posted By OHT
McMaster-Carr has quite a few cam type latches. ...

McMaster-Carr has quite a few cam type latches. Page 2936 may have some similar to your needs.

http://www.mcmaster.com/#cam-latches/=6nxk2x
Forum: Shop & Safety 12-02-2009, 11:40 PM
Replies: 17
Views: 3,369
Posted By OHT
calweld, I agree the low oil press shut-off is a...

calweld, I agree the low oil press shut-off is a pain. I've just gotten use to it I guess.

My K4000 only has 3 holes. Is there a different head (jaw) you can buy that works better?
Forum: Shop & Safety 12-02-2009, 10:28 AM
Replies: 17
Views: 3,369
Posted By OHT
Thank you for the replies. I’m worse than an old...

Thank you for the replies. I’m worse than an old woman. Below is the thinking process, or lack of, over last couple of weeks just for the compressor.

1. Need a 20+ cfm engine drive for stand...
Forum: Shop & Safety 11-27-2009, 04:31 PM
Replies: 17
Views: 3,369
Posted By OHT
Champion, Curtis, Jenny, or IR Engine Driven Compressor

I would like to put a welding skid together. I’ve been obsessing over the compressed air possibilities, type, manufacturer, etc. Finally decided on a standard service truck type engine driven...
Forum: Mechanical & Electrical 11-03-2009, 11:16 PM
Replies: 63
Views: 8,283
Posted By OHT
Interesting? My order was placed 10-15-2009. I...

Interesting? My order was placed 10-15-2009. I received "Order Acknowledgement" post card a few days later. Then couple of weeks ago the dreaded cancellations card, but no phone call.

The...
Forum: Mechanical & Electrical 10-17-2009, 09:41 PM
Replies: 63
Views: 8,283
Posted By OHT
When I saw this post a couple days ago I ordered...

When I saw this post a couple days ago I ordered one (Thanks I think).

If the specs at HF are correct this is the same as #93274 (US560V). Here is the owner's manual for that compressor.
...
Forum: Welding 03-04-2008, 08:44 PM
Replies: 2
Views: 1,273
Posted By OHT
I assUme it’s the correct handle. That’s...

I assUme it’s the correct handle. That’s probably my first mistake. The torch body threads are .925” OD and the torch handle (ribbed side) is .870” ID?? Can’t find any PN’s on the handle.

Yea,...
Forum: Welding 03-04-2008, 07:23 PM
Replies: 2
Views: 1,273
Posted By OHT
Weldcraft WP-26FV Torch Handle Install?

I'm having a problem getting the ribbed handle on a Weldcraft WP-26FV torch body. My other torches (WP-17 and WP-24) just slide on over the ribs on the torch body (some force required). The WP-26FV...
Forum: Welding 02-07-2008, 10:31 PM
Replies: 17
Views: 8,474
Posted By OHT
I replaced the crappy short input cable on a...

I replaced the crappy short input cable on a Lincoln SP-175+ with 35’ of 10-3 soow. I also replaced ground cable with a #4 and better ground clamp. May be my imagination but it seems to weld...
Forum: Machining 11-17-2007, 08:36 PM
Replies: 18
Views: 2,628
Posted By OHT
I have a little 12x36 that came with a B size...

I have a little 12x36 that came with a B size (200) tool post and just a few holders. I ordered the set from CDCO Machinery Corp. (cdcotools.com) just to get the tool holders. The price was right...
Forum: Blacksmithing & Forming 09-23-2007, 09:03 AM
Replies: 7
Views: 2,027
Posted By OHT
Good blacksmith form

Check this form out. All you ever wanted to know about anvils. Lots of good info on forging.

http://www.anvilfire.com/
Forum: Fabrication 09-10-2007, 10:43 PM
Replies: 41
Views: 7,328
Posted By OHT
Kids love heat and hammers

Nick,
My kids thought welding and machining stuff was pretty cool until I did some crude work forging some parts one day. If you have a O/A or O/P torch I think you could make the feet your...
Showing results 1 to 15 of 15

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 06:10 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.