Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 4758
Search took 0.51 seconds.
Search: Posts Made By: GWIZ
Forum: Mechanical & Electrical Yesterday, 10:01 PM
Replies: 8
Views: 290
Posted By GWIZ
No, I only have access into General Technical...

No, I only have access into General Technical information..... it is in Mechanical & electrical......
Forum: Mechanical & Electrical Yesterday, 01:01 PM
Replies: 8
Views: 290
Posted By GWIZ
If it is I did not see it. ...

If it is I did not see it.

https://www.shopfloortalk.com/forums/showthread.php?t=13811
Forum: Welding 09-13-2019, 03:24 PM
Replies: 11
Views: 686
Posted By GWIZ
Using a battery clamp for welding does a poor job...

Using a battery clamp for welding does a poor job the points/teeth do not pass a lot of amps, not enough surface contact, found out when I got rid of the same type of clamp.....
get a real welding...
Forum: Mechanical & Electrical 09-12-2019, 09:30 PM
Replies: 47
Views: 1,359
Posted By GWIZ
:rolleyes: I was waiting for you to...

:rolleyes:


I was waiting for you to finish the Instructions from post 39. but figured you were working on something bigger.

cut the burn through spot off the wire, strip the wire and post the...
Forum: Welding 09-09-2019, 01:11 AM
Replies: 21
Views: 735
Posted By GWIZ
Take a piece of SS the width of the sink and glue...

Take a piece of SS the width of the sink and glue it on top wrap it down the front.
At least you will have two symmetrical lines and no gap.
Forum: Fabrication 09-06-2019, 07:05 PM
Replies: 28
Views: 1,216
Posted By GWIZ
Place the video on Youtube and send a link to the...

Place the video on Youtube and send a link to the sanitation company.
Also state it looks like hit and run if he did not leave contact information.
Forum: Mechanical & Electrical 09-06-2019, 06:45 PM
Replies: 47
Views: 1,359
Posted By GWIZ
your quote was confusing as saying "no reading" "...

your quote was confusing as saying "no reading" " each wire.", figured the except was on the anneal switch.

Anyway.
correct me if I'm wrong the short to ground is in the motor and now we need to...
Forum: Mechanical & Electrical 09-06-2019, 02:33 PM
Replies: 47
Views: 1,359
Posted By GWIZ
once you get a reading you should start isolating...

once you get a reading you should start isolating from there on.
you say the anneal switch is clean from leakage to ground (just noting you unbolted its cover from the rest of the machines metals...
Forum: Mechanical & Electrical 09-05-2019, 10:44 AM
Replies: 47
Views: 1,359
Posted By GWIZ
in this circuit You should not get any meter...

in this circuit You should not get any meter readings to the frame/ground.
in other words no continuity to the frame/ground.
---
(this is "technically wrong" on my part because resistance and...
Forum: Mechanical & Electrical 09-04-2019, 10:28 PM
Replies: 47
Views: 1,359
Posted By GWIZ
You will have to systematically disconnect each...

You will have to systematically disconnect each wire until your meter does not read a short.

remove the wires from the anneal switch and probe each terminal on the switch from ground then each...
Forum: Mechanical & Electrical 09-03-2019, 08:06 PM
Replies: 47
Views: 1,359
Posted By GWIZ
That is not good. 22.4 ohms to ground. ...

That is not good.

22.4 ohms to ground.

You will have to systematically disconnect wires until your meter does not read a short.
disconnect the two motor wires and check the motor out of the...
Forum: Mechanical & Electrical 09-03-2019, 03:53 PM
Replies: 47
Views: 1,359
Posted By GWIZ
we use an ohm meter to confirm ground problems. ...

we use an ohm meter to confirm ground problems.

you confirmed the motor is pulling 4 amps
that tells me "if" there is a ground short it is a pretty hard-short/strong, so using the 2000 ohm scale...
Forum: Mechanical & Electrical 09-03-2019, 01:24 AM
Replies: 47
Views: 1,359
Posted By GWIZ
yep.....Bold

yep.....Bold
Forum: Mechanical & Electrical 09-03-2019, 12:23 AM
Replies: 47
Views: 1,359
Posted By GWIZ
I assume you are measuring from ground. From...

I assume you are measuring from ground.

From your readings L1 maybe open......
Do this
turn off all power to the saw
disconnect L1 and L2
lay them somewhere on something insulated so you can...
Forum: Mechanical & Electrical 09-02-2019, 03:19 PM
Replies: 47
Views: 1,359
Posted By GWIZ
I'll have to read your two posts a bit later. ...

I'll have to read your two posts a bit later.

turn off the power and
Disconnect L1 and L2
set your meter about the 2000 ohm range and check for ground leakage

one probe to the metal case and...
Forum: Mechanical & Electrical 09-02-2019, 11:24 AM
Replies: 47
Views: 1,359
Posted By GWIZ
by the drawing you have two wires that may feed...

by the drawing you have two wires that may feed power (H1 and) so as I asked pull the 10 amp anneal fuse and see if the motor stops.
Forum: Mechanical & Electrical 09-01-2019, 04:09 PM
Replies: 47
Views: 1,359
Posted By GWIZ
If the anneal switch came a part in side its self...

If the anneal switch came a part in side its self (half ass short) it just may get power.

note L2 also feeds to H4.

pull the 10amp fuse and see if that stops the motor, that would be the anneal...
Forum: Mechanical & Electrical 09-01-2019, 12:03 AM
Replies: 47
Views: 1,359
Posted By GWIZ
Yep a stuck weld switch it switches on the...

Yep a stuck weld switch it switches on the primary power. AND starts the motor.
Forum: Mechanical & Electrical 08-31-2019, 07:49 PM
Replies: 47
Views: 1,359
Posted By GWIZ
A real quick look without too much thinking just...

A real quick look without too much thinking just maybe the weld button is stuck on, or somewhat making a connection it should not be.
Forum: Mechanical & Electrical 08-30-2019, 11:00 PM
Replies: 17
Views: 586
Posted By GWIZ
I seen that goofy Starter switch quite a few...

I seen that goofy Starter switch quite a few times and wondered about them never had problems so I did not look any further.

Your post got the best of me.
The first thing we know it Disconnects...
Forum: Mechanical & Electrical 08-29-2019, 11:37 AM
Replies: 17
Views: 586
Posted By GWIZ
1) And a centrifugal "start" switch to go with...

1) And a centrifugal "start" switch to go with it, some GE's used a current sensing start relay.

2) Yes low load/hp fan Motors, noticeably 3 times more copper wire and thinner.
Forum: Mechanical & Electrical 08-29-2019, 12:44 AM
Replies: 17
Views: 586
Posted By GWIZ
You are right, I am pretty sure that is the same...

You are right, I am pretty sure that is the same motor I have in my washing machine with the exception he has a straight shaft.
the wiring colors seem to match the drawing I posted.

not that I...
Forum: Mechanical & Electrical 08-28-2019, 10:53 PM
Replies: 17
Views: 586
Posted By GWIZ
1) yes and that will likely pull double the...

1) yes and that will likely pull double the amps..... not good!


2) yes Looks like a DPDT "with center off" can work
the start circuit "Must" also be off at center position (or you can burn it...
Forum: Mechanical & Electrical 08-28-2019, 05:56 PM
Replies: 17
Views: 586
Posted By GWIZ
The centrifugal switch removes the "cap and start...

The centrifugal switch removes the "cap and start winding" from power once the motor gets up to 80% rpm, only used for starting otherwise they burn up.

assuming you have the centrifugal switch...
Forum: Mechanical & Electrical 08-28-2019, 12:35 AM
Replies: 17
Views: 586
Posted By GWIZ
Is this close?

Is this close?
Showing results 1 to 25 of 4758

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 05:44 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.