Forum: Machining
05-23-2022, 11:32 AM
|
|
Replies: 22
Views: 404
|
|
Forum: Machining
05-22-2022, 07:49 AM
|
|
Replies: 22
Views: 404
My guess is that it is a draw bar already. I...
My guess is that it is a draw bar already. I think the wheel is the jam nut. You could probably just loosen it be hand and change the taper out in the other end. It looks like about a 30 taper? ...
|
|
Forum: Machining
05-21-2022, 10:25 PM
|
|
Replies: 22
Views: 404
|
|
Forum: Mechanical & Electrical
05-21-2022, 08:14 PM
|
|
Replies: 15
Views: 380
|
|
Forum: Machining
05-20-2022, 08:37 PM
|
|
Replies: 4
Views: 207
|
|
Forum: Machining
05-20-2022, 04:43 PM
|
|
Replies: 4
Views: 207
|
|
Forum: Machining
05-19-2022, 09:17 AM
|
|
Replies: 8
Views: 236
HES Lathe
Thanks Scott. The video and PDF makes it look easy. This will help me figure it out.
Good thing I still have an analog meter or two still around.
Sent from my iPhone using Tapatalk
|
|
Forum: Fabrication
05-19-2022, 05:44 AM
|
|
Replies: 9
Views: 398
I think it will distort a bit. Depends on how...
I think it will distort a bit. Depends on how hot you get it if you use the cut off wheel. You will get to practice your blacksmithing skills to get it back into shape, but it should conform back...
|
|
Forum: Machining
05-18-2022, 08:41 PM
|
|
Replies: 8
Views: 236
HES Lathe
Short for H. Ernault-Somua company, made in France
Type 550,
Numero (serial # ?) 10799
Date de sortie 28369
20” swing, 94” overall bed length about 64” between centers, if I had a center for...
|
|
Forum: Machining
05-17-2022, 09:18 AM
|
|
Replies: 4
Views: 207
question for Ron
Lubrication question for Ron.
I might have more later, but will start with this.
Hopefully you can make out in picture what it calls for in the Headstock. Lathe was made in France in 1969.
...
|
|
Forum: Fabrication
05-07-2022, 06:10 AM
|
|
Replies: 13
Views: 443
Rotisserie for Willys jeep restoration
I made a rotisserie for making and painting handrails at previous job. Similar to your design, minus the wheels. I used it for several different projects later. I made walk brackets that hung each...
|
|
Forum: Fabrication
05-06-2022, 05:36 AM
|
|
Replies: 7
Views: 331
|
|
Forum: Mechanical & Electrical
05-04-2022, 05:44 AM
|
|
Replies: 34
Views: 1,292
|
|
Forum: Mechanical & Electrical
05-01-2022, 12:32 PM
|
|
Replies: 20
Views: 826
Cute little dozer.
I had a regular smaller...
Cute little dozer.
I had a regular smaller dozer 15 years ago. I forgot the make, but I I think it weighed under 5000 #. I regret selling it. It was a worn out, piece that was modified with a...
|
|
Forum: Machining
05-01-2022, 12:17 PM
|
|
Replies: 15
Views: 821
Primitive shop methods
I take a lot of things for granted in my work shop and home shop compared to those work conditions.
Couple take aways that I seen ( maybe not the first time, but reminds me of a trick)
Using...
|
|
Forum: Machining
05-01-2022, 08:23 AM
|
|
Replies: 20
Views: 843
|
|
Forum: Machining
04-29-2022, 11:25 AM
|
|
Replies: 69
Views: 4,620
Thanks for posting your math sheet. I can’t...
Thanks for posting your math sheet. I can’t quite remember those problems from high school math classes, but I probably did something similar. Just not using that education for 32 years makes it a...
|
|
Forum: Machining
04-28-2022, 09:01 AM
|
|
Replies: 20
Views: 843
measuring keyways
Heck, how many of any of the population would know how to do square root by hand? Math was one of my strong subjects in school, but if you asked me to much of the advanced math, I would struggle...
|
|
Forum: Machining
04-27-2022, 11:11 AM
|
|
Replies: 20
Views: 843
I would have to check machinist handbook for...
I would have to check machinist handbook for sure, but typically I just touch off the Od, and take my 1/2 key depth from there. I will usually add .010” to this, because I want to make sure...
|
|
Forum: Machining
04-26-2022, 11:05 PM
|
|
Replies: 95
Views: 4,342
Ehrlich/IXL Lathe
Let the fun learning begin!
You will get all kinds of advice now. Some will be directly applicable to you, and some will not apply to you at all with your "Small" lathe set up. This will be...
|
|
Forum: Fabrication
04-25-2022, 05:51 AM
|
|
Replies: 4
Views: 453
|
|
Forum: Welding
04-24-2022, 07:37 PM
|
|
Replies: 35
Views: 2,013
|
|
Forum: Welding
04-23-2022, 03:52 PM
|
|
Replies: 35
Views: 2,013
|
|
Forum: Machining
04-19-2022, 02:02 PM
|
|
Replies: 69
Views: 4,620
Sounds good to me. Let us know how it turns...
Sounds good to me. Let us know how it turns out.[emoji38]
Seriously though, will you do a test run before cutting to verify your figuring? Or just trust your math?
This is a pretty...
|
|
Forum: Fabrication
04-19-2022, 11:38 AM
|
|
Replies: 21
Views: 1,419
I will agree that the guy in the video seems a...
I will agree that the guy in the video seems a bit off. But then again, when you meet a nerd who really understands computers, aren’t they a bit off too? Computer guys that understand computers...
|
