Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 6107
Search took 0.54 seconds.
Search: Posts Made By: digr
Forum: Machining Yesterday, 07:25 PM
Replies: 5
Views: 132
Posted By digr
Perfect!!!!!!!!!!

Perfect!!!!!!!!!!
Forum: Shop & Safety 09-16-2019, 03:08 PM
Replies: 226
Views: 57,373
Posted By digr
Me too

Me too
Forum: Fabrication 09-15-2019, 05:26 PM
Replies: 20
Views: 634
Posted By digr
I usually braze those, looks good

I usually braze those, looks good
Forum: Mechanical & Electrical 09-15-2019, 04:13 PM
Replies: 6
Views: 234
Posted By digr
A long bar works for me

A long bar works for me
Forum: Mechanical & Electrical 09-15-2019, 04:09 PM
Replies: 8
Views: 223
Posted By digr
With that clamp it might last forever but then...

With that clamp it might last forever but then again:eek: I would slide a piece of pipe over the cable leaving a tad sticking out and spread it a little and take a torch and melt the cable to the...
Forum: Mechanical & Electrical 09-15-2019, 02:43 PM
Replies: 8
Views: 223
Posted By digr
Yup and never saddle a dead horse ...

Yup and never saddle a dead horse (https://www.absoluterescue.com/training/never-saddle-dead-horse/)
Forum: Mechanical & Electrical 09-12-2019, 05:21 PM
Replies: 3
Views: 169
Posted By digr
Big Carl

Big ass crane (https://www.bbc.com/news/uk-england-somerset-49673561)
Forum: Welding 09-11-2019, 10:29 AM
Replies: 6
Views: 306
Posted By digr
Looks good from up here!!

Looks good from up here!!
Forum: Mechanical & Electrical 09-10-2019, 10:54 AM
Replies: 8
Views: 325
Posted By digr
Electric motor parts

Great source for electric motor parts (http://www.carbonbrush.com/)
Forum: Mechanical & Electrical 09-09-2019, 07:50 PM
Replies: 12
Views: 425
Posted By digr
Scotts got it...

Scotts got it (https://hardwickandsons.com/products/general-tools-hardened-steel-mini-pocket-scribe)
Forum: Welding 09-09-2019, 07:14 AM
Replies: 21
Views: 758
Posted By digr
Run!!!!!!

Run!!!!!!
Forum: Fabrication 09-07-2019, 09:45 PM
Replies: 3
Views: 333
Posted By digr
Thanks for the heads up I think you found the...

Thanks for the heads up I think you found the answer! (https://www.youtube.com/watch?v=mVQDa0J1x5c)
Forum: Fabrication 09-07-2019, 05:17 PM
Replies: 3
Views: 333
Posted By digr
Fuel tank

The man wanted his old headache rack and a new fuel tank mounted on his 2011 Ford F350 and still have his roll up Tonneau Cover mounted behind it. Does anyone have any ideas for a rubber molding to...
Forum: Machining 09-07-2019, 06:52 AM
Replies: 12
Views: 367
Posted By digr
The tip of the oil can depresses the ball

The tip of the oil can depresses the ball
Forum: Fabrication 09-06-2019, 07:24 PM
Replies: 28
Views: 1,245
Posted By digr
Put a chain on it and use a come along.

Put a chain on it and use a come along.
Forum: Mechanical & Electrical 09-06-2019, 06:31 PM
Replies: 179
Views: 7,498
Posted By digr
Boy gaskets sure have come a long way scene the...

Boy gaskets sure have come a long way scene the old days
Forum: Machining 09-06-2019, 03:36 PM
Replies: 12
Views: 367
Posted By digr
I usually find them at yard sales

I usually find them at yard sales
Forum: Mechanical & Electrical 09-06-2019, 03:34 PM
Replies: 47
Views: 1,403
Posted By digr
In the pre meter days I used a battery charger to...

In the pre meter days I used a battery charger to check continuity:eek: It worked OK until the newer electronics wouldn't carry the load.:D
Forum: Machining 09-06-2019, 12:58 PM
Replies: 12
Views: 367
Posted By digr
getts button oilers...

getts button oilers...
Forum: Mechanical & Electrical 09-06-2019, 10:49 AM
Replies: 179
Views: 7,498
Posted By digr
I wonder if a needle gun would work?

I wonder if a needle gun would work?
Forum: Mechanical & Electrical 09-05-2019, 01:31 PM
Replies: 179
Views: 7,498
Posted By digr
Ether that or just weight until he leaves town

Ether that or just weight until he leaves town
Forum: Shop & Safety 09-03-2019, 07:07 AM
Replies: 37
Views: 1,979
Posted By digr
Its gonna be nice!!!! How many times have you...

Its gonna be nice!!!! How many times have you arranged your tools, welders and benches in your mind???

Ted
Forum: Machining 09-01-2019, 11:33 AM
Replies: 19
Views: 705
Posted By digr
NO!!! I will not tell you that, if it is in...

NO!!! I will not tell you that, if it is in descent shape I would go for it, that's a great price IMO. And remember its always nice to have a second lathe:D
Forum: Machining 09-01-2019, 10:17 AM
Replies: 11
Views: 633
Posted By digr
More ith the boring bars

Saw the ad for a bar holder and figured that I could come under budget if I made it.
Forum: Mechanical & Electrical 08-28-2019, 06:13 PM
Replies: 17
Views: 599
Posted By digr
Hey I was right

Hey I was right
Showing results 1 to 25 of 6107

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 10:15 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.