Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 6554
Search took 0.16 seconds.
Search: Posts Made By: digr
Forum: Welding 04-15-2021, 06:41 PM
Replies: 9
Views: 236
Posted By digr
Try not to breath those fumes from that rod. The...

Try not to breath those fumes from that rod. The only thing I can think of as long as your heat and polarity are right it might be ark blow, try moving your ground.
Forum: Mechanical & Electrical 04-11-2021, 10:35 AM
Replies: 2
Views: 193
Posted By digr
Wood spliter

Looks like it works pretty good (https://www.youtube.com/watch?v=kIAWfzcTc8o)
Forum: Mechanical & Electrical 04-10-2021, 06:49 PM
Replies: 10
Views: 423
Posted By digr
Gad you found the problem! I have made wooden...

Gad you found the problem! I have made wooden alignment shafts out of wood on the lathe for oddball stuff.
Forum: Fabrication 04-04-2021, 10:19 AM
Replies: 22
Views: 1,296
Posted By digr
When I make steps I tack two pieces of flat bar...

When I make steps I tack two pieces of flat bar together and drill along the center then separate.
Forum: Fabrication 04-03-2021, 09:59 AM
Replies: 22
Views: 1,296
Posted By digr
Every little bit helps.

Every little bit helps.
Forum: Fabrication 04-02-2021, 07:12 AM
Replies: 3
Views: 270
Posted By digr
With a good blade I don't see any problem.

With a good blade I don't see any problem.
Forum: Mechanical & Electrical 04-01-2021, 04:56 PM
Replies: 9
Views: 275
Posted By digr
Did you check that red wire?

Did you check that red wire?
Forum: Mechanical & Electrical 04-01-2021, 03:56 PM
Replies: 9
Views: 275
Posted By digr
One red wire on the left looks like its having...

One red wire on the left looks like its having trouble
Forum: Mechanical & Electrical 04-01-2021, 03:49 PM
Replies: 9
Views: 275
Posted By digr
Do they work without the cover on?

Do they work without the cover on?
Forum: Mechanical & Electrical 03-31-2021, 12:46 PM
Replies: 37
Views: 1,307
Posted By digr
You have enough machinery to level everything out...

You have enough machinery to level everything out Why would you need to buy a special mower?
Forum: Fabrication 03-31-2021, 10:24 AM
Replies: 2
Views: 322
Posted By digr
Wood processor

The man asked to make this wood processor ole man friendly. It came with a 800# non reversible hand winch with no way to flip the end conveyor over for transport. It took two men and a boy to raise...
Forum: Fabrication 03-24-2021, 10:23 AM
Replies: 13
Views: 1,050
Posted By digr
A hellofa nice job, lots of work!!!

A hellofa nice job, lots of work!!!
Forum: Welding 03-24-2021, 10:02 AM
Replies: 19
Views: 1,061
Posted By digr
Something that thick if mild steel I would use...

Something that thick if mild steel I would use enough heat to warm it to the touch and no worry about post heat. Post a pic of the steel and welcome to the site!
Forum: Fabrication 03-23-2021, 12:52 PM
Replies: 5
Views: 451
Posted By digr
Perfect!!!!!!

Perfect!!!!!!
Forum: Machining 03-21-2021, 12:12 PM
Replies: 6
Views: 641
Posted By digr
Success!!!!!! Took a fine tooth carbide blade...

Success!!!!!! Took a fine tooth carbide blade from my skill saw and used the table saw and it was a piece of cake:D Thank's for the advice. I have cut aluminum before but always used a coarse blade...
Forum: Machining 03-20-2021, 08:36 PM
Replies: 6
Views: 641
Posted By digr
Best way to cut

The man wants the legs cut off of these aluminum channels which are three feet long and less than a 1/8" thick. they are going to show when done so he wants them nice and neat. He wants the leg cut...
Forum: Machining 03-16-2021, 12:57 PM
Replies: 0
Views: 396
Posted By digr
AXA tool holder

All Industrial (https://allindustrial.com/colton-industrial-tools-97103-axa-2-xl-extra-capacity-5-8-turning-facing-quick-change-tool-holder-250-102xl-with-upgraded-zin-coated-hardware/) has AXA tool...
Forum: Fabrication 03-14-2021, 11:04 AM
Replies: 5
Views: 930
Posted By digr
Looking good!!

Looking good!!
Forum: Mechanical & Electrical 03-13-2021, 04:39 PM
Replies: 17
Views: 916
Posted By digr
Nice clean cuts, especially in pine. Looking good!

Nice clean cuts, especially in pine. Looking good!
Forum: Fabrication 03-01-2021, 05:42 PM
Replies: 28
Views: 2,064
Posted By digr
Did you have the air holes "UNDER" the carbon...

Did you have the air holes "UNDER" the carbon rod?
Forum: Shop & Safety 02-23-2021, 04:16 PM
Replies: 38
Views: 3,360
Posted By digr
Goodwill jewelry box

Goodwill jewelry box
Forum: Machining 02-23-2021, 01:32 PM
Replies: 6
Views: 617
Posted By digr
Its a done deal. Turned the end down to .075"with...

Its a done deal. Turned the end down to .075"with a over size bushing pressed on with loctite then turned to size.
Forum: Fabrication 02-20-2021, 09:14 PM
Replies: 25
Views: 1,626
Posted By digr
Sorry to hear that! Three days WOW it would take...

Sorry to hear that! Three days WOW it would take me three weeks. Hell of a nice job!!

Ted
Forum: Fabrication 02-19-2021, 10:31 PM
Replies: 18
Views: 1,334
Posted By digr
Never heard of such a thing

Never heard of such a thing
Forum: Machining 02-19-2021, 09:47 PM
Replies: 6
Views: 617
Posted By digr
Drive shaft

This is a drive shaft off a tractor 1 1/8" dia. and four feet long without a carrier bearing. The splined end is 7/8" that goes threw the clutch plate into a bearing in the flywheel. It is 030" under...
Showing results 1 to 25 of 6554

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 09:09 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.