Forum: Fabrication
06-10-2013, 04:09 PM
|
Replies: 10
Views: 2,508
|
Forum: Fabrication
06-10-2013, 02:03 PM
|
Replies: 10
Views: 2,508
|
Forum: Fabrication
06-10-2013, 02:03 PM
|
Replies: 10
Views: 2,508
Pipe question
I bought a couple pieces of 24" pipe to build BBQ pits with. After getting ready to mount end caps I realized out of round it was. How close to round is pipe this size usually? These are almost...
|
Forum: Fabrication
01-11-2013, 10:18 AM
|
Replies: 18
Views: 3,894
|
Forum: Fabrication
01-04-2013, 04:32 PM
|
Replies: 18
Views: 3,894
|
Forum: Fabrication
01-04-2013, 04:06 PM
|
Replies: 18
Views: 3,894
|
Forum: Fabrication
01-04-2013, 04:05 PM
|
Replies: 18
Views: 3,894
|
Forum: Fabrication
01-04-2013, 03:14 PM
|
Replies: 18
Views: 3,894
Pipe End Caps for BBQ Pit
I built a bbq pit recently for a friend and am about to start a second one. On the first one I cut circles with my plasma and welded them in to cap the ends. Then I ground the welds. The end cap...
|
Forum: Fabrication
12-06-2012, 09:48 AM
|
Replies: 17
Views: 4,160
|
Forum: Fabrication
12-05-2012, 10:57 PM
|
Replies: 17
Views: 4,160
Mitering round tube
Is there a good trick when mitering round tube on both ends to make sure the cuts are 'clocked' together?
Basically cutting 45's on both ends the another piece mitered to be the upright. Does that...
|
Forum: Welding
10-23-2012, 08:11 PM
|
Replies: 11
Views: 2,459
|
Forum: Shop & Safety
08-07-2012, 10:15 AM
|
Replies: 7
Views: 2,279
|
Forum: Shop & Safety
07-30-2012, 06:21 PM
|
Replies: 7
Views: 2,279
Generator/Electrical Question
Just got a travel trailer....a 'new to me' special. I'd never had one before. So I went to a bbq cook off and set up camp. Had to power off of a generator (Northern Tool's NorthStar brand,...
|
Forum: Shop & Safety
06-12-2012, 01:43 PM
|
Replies: 10
Views: 3,960
So I got a new compressor....
And I have a couple questions. My previous compressors have always been Craftsman single stage oil-less types and came with a regulator, etc.
My new compressor is a 60 gallon, 2 stage with 1/2"...
|
Forum: Fabrication
05-04-2012, 08:45 AM
|
Replies: 17
Views: 3,663
|
Forum: Fabrication
05-03-2012, 08:43 AM
|
Replies: 17
Views: 3,663
|
Forum: Fabrication
05-01-2012, 05:34 PM
|
Replies: 17
Views: 3,663
|
Forum: Fabrication
05-01-2012, 12:00 PM
|
Replies: 17
Views: 3,663
|
Forum: Fabrication
05-01-2012, 11:32 AM
|
Replies: 17
Views: 3,663
Corner beveler???
I'm going to be welding up some fireboxes for a couple BBQ pits. I have a custom pit that I had built by a professional pit builder and the outside corners are so square/straight that I can't imagine...
|
Forum: Mechanical & Electrical
08-05-2011, 08:42 PM
|
Replies: 5
Views: 2,040
|
Forum: Mechanical & Electrical
08-05-2011, 01:38 PM
|
Replies: 5
Views: 2,040
Crooked End Bar?
Anybody heard of a crooked end bar? Not sure of the proper name, that's what we've always called them. It's about 4 foot long with about a 60 degree bend at one end and necks down to somewhat sharp...
|