Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums
Reload this Page Search Results
Register FAQ Members List Social Groups Calendar Search Today's Posts Mark Forums Read

SFT Search:   
Showing results 1 to 21 of 21
Search took 0.01 seconds. Search: Posts Made By: 5500bill
Forum: Shop & Safety 12-02-2020, 01:56 PM
Replies: 6
Views: 583
Posted By 5500bill
Stairs are a good one to watch out for especially...

Stairs are a good one to watch out for especially if carrying something. I live alone always have my cell phone also have an apple watch that I can call from. I am more careful than I have ever been...
Forum: Shop & Safety 07-09-2020, 07:40 AM
Replies: 9
Views: 1,324
Posted By 5500bill
My brother had ants in his mail on the side of...

My brother had ants in his mail on the side of the road, a couple of dryer sheets and they were gone
Forum: Machining 02-12-2020, 11:27 AM
Replies: 24
Views: 1,810
Posted By 5500bill
Could spray it down with Fluid Film

Could spray it down with Fluid Film
Forum: Mechanical & Electrical 01-11-2020, 08:01 PM
Replies: 54
Views: 5,734
Posted By 5500bill
just throwing this out there have you checked the...

just throwing this out there have you checked the grounds battery to engine and battery to frame and battery to body. one test we used to do was take a test light or meter one lead to neg battery...
Forum: Mechanical & Electrical 10-14-2019, 08:09 PM
Replies: 15
Views: 3,182
Posted By 5500bill
Is the truck equipped with the factory trailer...

Is the truck equipped with the factory trailer tow if it is there are relays for each turn signal and tail lights and brake lights and fuses for each to the harness to the rear of the truck. If you...
Forum: Mechanical & Electrical 09-30-2019, 08:22 PM
Replies: 21
Views: 2,398
Posted By 5500bill
on Fords the s means a splice and the number is...

on Fords the s means a splice and the number is the number for the splice if you had what ford calls a EVTM (electrical vacuum trouble shooting manual) it would tell the location of the splice. I...
Forum: Mechanical & Electrical 09-28-2019, 10:40 PM
Replies: 42
Views: 4,688
Posted By 5500bill
Wasn't there a thread about lube in the gear box...

Wasn't there a thread about lube in the gear box on bandsaws because of the bronze gears and excessive wear or damage to the gears
Forum: Mechanical & Electrical 05-04-2019, 09:37 PM
Replies: 8
Views: 1,073
Posted By 5500bill
on a gas engine I would use a vacuum port on the...

on a gas engine I would use a vacuum port on the manifold but a diesel I would use the ac vacuum pump but keep the fluid level low enough so the fluid does not get sucked into the pump. It will sound...
Forum: Mechanical & Electrical 05-04-2019, 06:50 PM
Replies: 8
Views: 1,073
Posted By 5500bill
Ford had an adapter to put on the reservoir in...

Ford had an adapter to put on the reservoir in place of the cap, and put the system under a vacuum and turn the wheel lock to lock, on most newer ford vehicles that was the only way to get the air...
Forum: Fabrication 09-04-2017, 09:40 PM
Replies: 9
Views: 2,491
Posted By 5500bill
The tool is used to separate the shift linkage...

The tool is used to separate the shift linkage from the plastic grommet on Ford transmissions and transfer cases. I used it when I was working in a Ford dealership. Two well placed pry bars work...
Forum: Fabrication 11-26-2016, 05:17 PM
Replies: 38
Views: 11,275
Posted By 5500bill
Nice work

Nice work
Forum: Mechanical & Electrical 07-21-2016, 02:53 PM
Replies: 15
Views: 2,695
Posted By 5500bill
If you have all the injectors out pull the valve...

If you have all the injectors out pull the valve cover back off the rocker arm hold down bolts so the valves are closed. put shop air to it see if it comes out any where engine will probably turn...
Forum: Shop & Safety 12-04-2015, 01:51 PM
Replies: 35
Views: 11,934
Posted By 5500bill
Modules like abs any body control modules some...

Modules like abs any body control modules some radios instrument clusters
Forum: Shop & Safety 12-03-2015, 11:16 AM
Replies: 35
Views: 11,934
Posted By 5500bill
If memory serves me correctly when you put...

If memory serves me correctly when you put ammeter in series you will have to wait for all modules to go to sleep maybe 15 to 30 min draw should be .05amps that was we looked for on fords. I have not...
Forum: Fabrication 08-19-2015, 05:43 PM
Replies: 33
Views: 7,721
Posted By 5500bill
Looks better than factory, built the way you...

Looks better than factory, built the way you want, and no shortcuts
Forum: Fabrication 08-17-2015, 11:52 AM
Replies: 33
Views: 7,721
Posted By 5500bill
Grote makes a flasher for that. Should be...

Grote makes a flasher for that. Should be available at parts store. The technical term is hyper flashing Google it and you should be able to com up with a part number
Forum: Shop & Safety 07-13-2015, 07:28 PM
Replies: 137
Views: 39,552
Posted By 5500bill
I like the wheels on your chop saw

I like the wheels on your chop saw
Forum: Mechanical & Electrical 05-21-2015, 08:01 PM
Replies: 45
Views: 9,976
Posted By 5500bill
I got mine around 5:00 pm did not realize they...

I got mine around 5:00 pm did not realize they made them that big. Thanks for the heads up on getting the free samples
Forum: Fabrication 04-13-2015, 08:44 PM
Replies: 21
Views: 8,255
Posted By 5500bill
good job on the repair, around here they would...

good job on the repair, around here they would not even think of welding it.
Forum: Fabrication 02-21-2013, 04:27 PM
Replies: 29
Views: 5,359
Posted By 5500bill
+1 on the puller using the 3 tapped holes. Put a...

+1 on the puller using the 3 tapped holes. Put a good pull on it and then hit the puller with hammer the shock should loosen the taper I have had good luck with this method
Forum: Fabrication 06-20-2012, 07:43 PM
Replies: 21
Views: 4,975
Posted By 5500bill
Hope things are going well in Maine no posts in...

Hope things are going well in Maine no posts in over 24 hours should we be concerned.
Showing results 1 to 21 of 21

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 10:44 PM.

Contact Us - Shop Floor Talk - Archive - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.