Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 6296
Search took 0.58 seconds.
Search: Posts Made By: digr
Forum: Machining 03-24-2020, 07:04 PM
Replies: 9
Views: 337
Posted By digr
Yup 3/4 and 1/2 inch plate, about half on the...

Yup 3/4 and 1/2 inch plate, about half on the lathe and half on the mill.
Forum: Machining 03-24-2020, 01:05 PM
Replies: 9
Views: 337
Posted By digr
Shelter in place vise

With a few improvements
Forum: Machining 03-24-2020, 06:46 AM
Replies: 22
Views: 509
Posted By digr
Nice job!!!! Ya know I have never silver soldered...

Nice job!!!! Ya know I have never silver soldered anything:confused:
Forum: Machining 03-23-2020, 03:40 PM
Replies: 22
Views: 509
Posted By digr
Would these be easier?...

Would these be easier? (https://www.buckeyefasteners.com/catalog/product/?cid=new-flat-head-carriage-bolts&id=FCB_2112)
Forum: Mechanical & Electrical 03-22-2020, 09:21 PM
Replies: 40
Views: 2,124
Posted By digr
Looks good

Looks good
Forum: Machining 03-21-2020, 06:35 AM
Replies: 6
Views: 311
Posted By digr
That will work

That will work
Forum: Mechanical & Electrical 03-20-2020, 06:00 PM
Replies: 20
Views: 466
Posted By digr
That sludge reminds of of the old days when my...

That sludge reminds of of the old days when my job was to clean out the sludge when my dad tore down a engine in the days before detergent oil showed up.
Forum: Fabrication 03-19-2020, 07:19 PM
Replies: 9
Views: 351
Posted By digr
I don't know if this will help but use a piece of...

I don't know if this will help but use a piece of angle and scribe a straight line then tack the pipe to a piece of channel then to the saw
Forum: Machining 03-19-2020, 10:59 AM
Replies: 4
Views: 304
Posted By digr
What I did was to use blocking and a jack to...

What I did was to use blocking and a jack to support the door when it is opened all the way then starting with the bottom hinge------

1 Use a die grinder to grind off the top of the pin and...
Forum: Machining 03-18-2020, 04:01 PM
Replies: 4
Views: 304
Posted By digr
Ford door hinge pins

Anyone need to change the ford F series or Bronco truck door hinge pins if so I have the tool for you that I made for repair on old 95 F 250 I believe the pins are the same from 89 to 97 and maybe...
Forum: Fabrication 03-18-2020, 03:43 PM
Replies: 13
Views: 670
Posted By digr
Wow that's a lot of work! how did you layout the...

Wow that's a lot of work! how did you layout the holes, do you have a indexing head?
Forum: Blacksmithing & Forming 03-15-2020, 09:01 PM
Replies: 3
Views: 166
Posted By digr
Great videos !!!!!!!!!!!!!!!!!!!!!!!!

Great videos !!!!!!!!!!!!!!!!!!!!!!!!
Forum: Fabrication 03-15-2020, 04:08 PM
Replies: 7
Views: 425
Posted By digr
Very nice!!!!!!!!!!!

Very nice!!!!!!!!!!!
Forum: Fabrication 03-08-2020, 01:05 PM
Replies: 19
Views: 1,004
Posted By digr
Excellent job on the chute!!!!!!!!!!

Excellent job on the chute!!!!!!!!!!
Forum: Fabrication 03-07-2020, 10:49 PM
Replies: 27
Views: 1,845
Posted By digr
That's usen the ol nogen!!! I like it

That's usen the ol nogen!!! I like it
Forum: Fabrication 03-03-2020, 01:07 PM
Replies: 12
Views: 3,305
Posted By digr
Take a look at this...

Take a look at this...
Forum: Fabrication 03-02-2020, 08:53 PM
Replies: 27
Views: 1,845
Posted By digr
There it was done. I spun the lift around to the...

There it was done. I spun the lift around to the back and wired so I can switch from foot pedal or the switch on the press.
Forum: Fabrication 03-01-2020, 01:27 PM
Replies: 27
Views: 1,404
Posted By digr
I have used this and it works good!...

I have used this and it works good!...
Forum: Mechanical & Electrical 02-28-2020, 10:19 PM
Replies: 40
Views: 2,124
Posted By digr
I wouldn't bother with the mill

I wouldn't bother with the mill
Forum: Welding 02-28-2020, 11:10 AM
Replies: 24
Views: 1,005
Posted By digr
Why not solder??

Why not solder??
Forum: Blacksmithing & Forming 02-28-2020, 08:22 AM
Replies: 27
Views: 3,603
Posted By digr
Well done!!! I like the forge.

Well done!!! I like the forge.
Forum: Fabrication 02-27-2020, 03:34 PM
Replies: 27
Views: 1,404
Posted By digr
I have cut and welded both propane bottles and...

I have cut and welded both propane bottles and gas tanks plus fuel tanks with no problem and all I will say is that I used air. Some people say that I am nuts or lucky, I have taken gas tanks and...
Forum: Machining 02-27-2020, 11:25 AM
Replies: 10
Views: 755
Posted By digr
The draw bar is not bottoming out??

The draw bar is not bottoming out??
Forum: Welding 02-24-2020, 10:20 PM
Replies: 8
Views: 627
Posted By digr
They are handy tool!!

They are handy tool!!
Forum: Fabrication 02-23-2020, 08:45 PM
Replies: 27
Views: 1,845
Posted By digr
I machined the collars from heavy wall pipe with...

I machined the collars from heavy wall pipe with .010" clearance.k The lift on my bench top has 6.250" travel which is plenty. The lift was from a hospital bed.
Showing results 1 to 25 of 6296

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 06:16 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.