Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 6137
Search took 0.60 seconds.
Search: Posts Made By: digr
Forum: Mechanical & Electrical Yesterday, 04:44 PM
Replies: 5
Views: 213
Posted By digr
I have never had a problem with them, maybe...

I have never had a problem with them, maybe because I have swivel heads.
Forum: Mechanical & Electrical 10-16-2019, 09:28 PM
Replies: 5
Views: 213
Posted By digr
Its to late for the learning part:devil:

Its to late for the learning part:devil:
Forum: Mechanical & Electrical 10-08-2019, 09:02 PM
Replies: 19
Views: 1,188
Posted By digr
The truck is finally done, fuel tank, headache...

The truck is finally done, fuel tank, headache rack, Tonneau Cover and backup camera and sensor bar.

1 headache rack and tank

2 bed cover and lift gate

3 sensor bar and camera mount

4...
Forum: Fabrication 10-07-2019, 04:50 PM
Replies: 24
Views: 1,220
Posted By digr
What is this outfit you work for going to do when...

What is this outfit you work for going to do when you retire?? Good luck

Ted
Forum: Blacksmithing & Forming 10-05-2019, 10:58 AM
Replies: 17
Views: 668
Posted By digr
Congratulations!!!! Ted

Congratulations!!!!

Ted
Forum: Shop & Safety 10-04-2019, 09:04 PM
Replies: 44
Views: 2,999
Posted By digr
One of my friends used to use a 22 to mark the...

One of my friends used to use a 22 to mark the center hole.
Forum: Shop & Safety 10-03-2019, 08:30 PM
Replies: 44
Views: 2,999
Posted By digr
My garage/shop has a 5/12 pitch with a tin roof....

My garage/shop has a 5/12 pitch with a tin roof. The first winter I ran six inch metalbestos pipe threw the roof to the proper height. I had it braced well inside the roof and I thought the pipe...
Forum: Mechanical & Electrical 10-03-2019, 05:26 PM
Replies: 42
Views: 1,347
Posted By digr
Why? the pipe looks good to me.

Why? the pipe looks good to me.
Forum: Fabrication 10-02-2019, 04:27 PM
Replies: 4
Views: 662
Posted By digr
Its done

Its done
Forum: Mechanical & Electrical 10-01-2019, 08:46 PM
Replies: 17
Views: 727
Posted By digr
I have had it happen where the threads in the...

I have had it happen where the threads in the pulley were bunged up and the set screw would tighten up without touching the key
Forum: Mechanical & Electrical 09-30-2019, 08:08 PM
Replies: 21
Views: 717
Posted By digr
I thought s138 and s137 to be a connection points...

I thought s138 and s137 to be a connection points for the fusible link
Forum: Mechanical & Electrical 09-30-2019, 07:18 PM
Replies: 21
Views: 717
Posted By digr
Not on this truck, look at the schematic, to find...

Not on this truck, look at the schematic, to find the link I would have to take the front right tire off, fender well and the air cleaner box and then cut into the harness is what i was going to do...
Forum: Mechanical & Electrical 09-30-2019, 06:30 PM
Replies: 21
Views: 717
Posted By digr
.

Well I got myself out of this nightmare, Ford said that they would have to replace the entire harness and they couldn't just get the link. I went to the scrap yard and they had nothing. Stopped at a...
Forum: Shop & Safety 09-30-2019, 06:07 PM
Replies: 44
Views: 2,999
Posted By digr
Its sure nice to have friends that are also...

Its sure nice to have friends that are also neighbors.
Forum: Mechanical & Electrical 09-30-2019, 11:25 AM
Replies: 12
Views: 430
Posted By digr
A you suck for sure!!!

A you suck for sure!!!
Forum: Mechanical & Electrical 09-30-2019, 07:32 AM
Replies: 42
Views: 1,347
Posted By digr
I think the saw is a home built unit, the only...

I think the saw is a home built unit, the only saw I have seen without a slanted saw frame is a Greeley.
Forum: Mechanical & Electrical 09-29-2019, 11:00 AM
Replies: 17
Views: 727
Posted By digr
When does this happen, on startup I would assume?...

When does this happen, on startup I would assume? It takes a lot to shear a key even with a sloppy pulley, could your pressure relief valve be hanging up?
Forum: Mechanical & Electrical 09-28-2019, 03:40 PM
Replies: 42
Views: 1,347
Posted By digr
1 the blade is junk 2 I get mine threw MSC ...

1 the blade is junk
2 I get mine threw MSC
3 bend the blade until it breaks then measure
4 ?????
5 new blade and square it with the vice and table
6 ????
Forum: Mechanical & Electrical 09-28-2019, 11:49 AM
Replies: 21
Views: 717
Posted By digr
Yes I did Thank's

Yes I did Thank's
Forum: Mechanical & Electrical 09-27-2019, 07:30 PM
Replies: 21
Views: 717
Posted By digr
Not mine

Not mine
Forum: Mechanical & Electrical 09-27-2019, 07:29 PM
Replies: 0
Views: 176
Posted By digr
Wiring

Professional Wiring Products (https://www.wiringdepot.com/)
Forum: Mechanical & Electrical 09-27-2019, 04:00 PM
Replies: 21
Views: 717
Posted By digr
What is the best way to repair?

What is the best way to repair?
Forum: Mechanical & Electrical 09-27-2019, 03:48 PM
Replies: 21
Views: 717
Posted By digr
As long as that wire is always hot does it matter...

As long as that wire is always hot does it matter which battery I use?
Forum: Mechanical & Electrical 09-27-2019, 03:19 PM
Replies: 21
Views: 717
Posted By digr
Fusible link

When I was wiring a lift gate on a 2011 Ford 7.3 powerstroke I hit the positive battery terminal with the ground cable and took out the alternator fusible link. I can't find the link because its...
Forum: Fabrication 09-26-2019, 07:38 PM
Replies: 4
Views: 572
Posted By digr
I wish someone would make a double Head 10 Degree...

I wish someone would make a double Head 10 Degree Offset box end wrench set for that kind of money, they all make a 45 degree offset set and all they are good for is rounding off bolt heads.
Showing results 1 to 25 of 6137

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 01:32 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.