Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 8173
Search took 0.80 seconds.
Search: Posts Made By: milomilo
Forum: Fabrication 11-26-2020, 10:39 PM
Replies: 17
Views: 645
Posted By milomilo
These seals had a ID to fit the spindle and a OD...

These seals had a ID to fit the spindle and a OD that had a 1/8" flange lip that fit in the hub ID up agianst the bearing race. If I had them out I could have got the P/N and a pic. I had not seen a...
Forum: Fabrication 11-25-2020, 10:23 PM
Replies: 17
Views: 645
Posted By milomilo
Warmed up a bit today (58)F so stripped off the...

Warmed up a bit today (58)F so stripped off the axle hubs and cleaned up all the bearings, seals and spindles. Bearings had sticky spots due to small dis in the spindles. Spent an hour with a small...
Forum: Fabrication 11-24-2020, 04:46 PM
Replies: 39
Views: 9,839
Posted By milomilo
I put the lip on the inside of the rim.

I put the lip on the inside of the rim.
Forum: Fabrication 11-24-2020, 11:56 AM
Replies: 39
Views: 9,839
Posted By milomilo
I do the bottom first also.

I do the bottom first also.
Forum: Fabrication 11-23-2020, 10:22 PM
Replies: 39
Views: 9,839
Posted By milomilo
Mine is still CW, original arm.

Mine is still CW, original arm.
Forum: Fabrication 11-23-2020, 07:36 PM
Replies: 39
Views: 9,839
Posted By milomilo
One of these days I will replace the 1/4hp with a...

One of these days I will replace the 1/4hp with a 1/2hp on mine.
Forum: Mechanical & Electrical 11-22-2020, 10:08 AM
Replies: 7
Views: 366
Posted By milomilo
Is it for a 225G?

Is it for a 225G?
Forum: Fabrication 11-21-2020, 11:53 AM
Replies: 9
Views: 660
Posted By milomilo
They doing the paint?

They doing the paint?
Forum: Machining 11-20-2020, 08:06 PM
Replies: 13
Views: 763
Posted By milomilo
Good point Sent from my iPhone using...

Good point


Sent from my iPhone using Tapatalk
Forum: Machining 11-20-2020, 07:34 PM
Replies: 13
Views: 763
Posted By milomilo
I have some heavy tin and I like the idea of a...

I have some heavy tin and I like the idea of a sled. Think I will try that out also.
Forum: Fabrication 11-20-2020, 09:40 AM
Replies: 17
Views: 645
Posted By milomilo
Seems I have a fetish for trailers as well as...

Seems I have a fetish for trailers as well as grinders.:D:D
Forum: Fabrication 11-19-2020, 07:24 PM
Replies: 17
Views: 645
Posted By milomilo
Last pics.

Last pics.
Forum: Fabrication 11-19-2020, 07:21 PM
Replies: 17
Views: 645
Posted By milomilo
More pics.

More pics.
Forum: Fabrication 11-19-2020, 07:18 PM
Replies: 17
Views: 645
Posted By milomilo
I have several drop and straight hitches I have...

I have several drop and straight hitches I have picked up over the years so likely I will find one in the pile that will work.

Finished up the demo and frame straightening, 2" ball hitch...
Forum: Mechanical & Electrical 11-18-2020, 10:02 PM
Replies: 5
Views: 365
Posted By milomilo
Maybe you could just filter it into a clean pail.

Maybe you could just filter it into a clean pail.
Forum: Fabrication 11-18-2020, 09:13 PM
Replies: 17
Views: 645
Posted By milomilo
The 4 wheeler's and the UTV all have receiver...

The 4 wheeler's and the UTV all have receiver hitches. The 4 wheeler's are much lower than a standard p/u and the utv is only half as much lower than a p/u. Expect the Ranger will be used most with...
Forum: Fabrication 11-18-2020, 06:37 PM
Replies: 17
Views: 645
Posted By milomilo
Thanks. Fixed.

Thanks. Fixed.
Forum: Fabrication 11-18-2020, 05:56 PM
Replies: 17
Views: 645
Posted By milomilo
More pics.

More pics.
Forum: Fabrication 11-18-2020, 05:46 PM
Replies: 17
Views: 645
Posted By milomilo
Anther Trailer Build

This is the trailer I got from a neighbor that was moving free. Pretty light unit but will be handy some times to have a flatbed to pull around the place with the Polaris Ranger or a 4 wheeler. Tires...
Forum: Mechanical & Electrical 11-18-2020, 03:10 PM
Replies: 7
Views: 366
Posted By milomilo
+1 on that.

+1 on that.
Forum: Mechanical & Electrical 11-17-2020, 07:24 PM
Replies: 7
Views: 304
Posted By milomilo
Did it freeze?

Did it freeze?
Forum: Machining 11-17-2020, 11:16 AM
Replies: 12
Views: 490
Posted By milomilo
The table looks good. Just needs cleaned up and...

The table looks good. Just needs cleaned up and oiled. At 1/4 the price of a better machine, it is worth the gamble. Tooling for it will equal the price of the machine.:eek:
Forum: Shop & Safety 11-17-2020, 09:50 AM
Replies: 285
Views: 55,971
Posted By milomilo
Looking forward to the new addition.:D

Looking forward to the new addition.:D
Forum: Shop & Safety 11-16-2020, 10:29 PM
Replies: 285
Views: 55,971
Posted By milomilo
With all that new space we will expect more...

With all that new space we will expect more projects from you.;)
Forum: Machining 11-16-2020, 10:26 PM
Replies: 7
Views: 345
Posted By milomilo
I think it sat in salt water a few years!!!!:eek:

I think it sat in salt water a few years!!!!:eek:
Showing results 1 to 25 of 8173

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 01:50 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.