Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 19 of 19
Search took 0.01 seconds.
Search: Posts Made By: troutback
Forum: Fabrication 05-31-2013, 04:38 PM
Replies: 34
Views: 6,026
Posted By troutback
well, i saw fish wheel and couldn't help but...

well,
i saw fish wheel and couldn't help but remember this....

https://www.youtube.com/watch?v=KezvwARhBIc
Forum: Machining 04-23-2013, 05:32 PM
Replies: 41
Views: 25,324
Posted By troutback
for those interested in flat belting,.... ...

for those interested in flat belting,....

there is a guy in pennsylvania who does leather or new material flat belt replacements. he has measurements for common machines like south bend lathes and...
Forum: Machining 03-07-2011, 01:54 PM
Replies: 20
Views: 3,658
Posted By troutback
well, the saga continues.... in order to...

well, the saga continues....

in order to order the d-60 "refurbish" kit, i had to call one of the repair centers. i was able to speak with a tech about this. the upshot is that they have never...
Forum: Machining 03-06-2011, 07:57 PM
Replies: 20
Views: 3,658
Posted By troutback
sorry for the image posting error. it's hard to...

sorry for the image posting error. it's hard to remember different website rules for attaching photos. my bad, and thanks for correcting.



there is a plate on it but all you can see is the...
Forum: Machining 03-06-2011, 06:28 PM
Replies: 20
Views: 3,658
Posted By troutback
my table is too small for the vise with out the...

my table is too small for the vise with out the base lol... but actually the broken part is great. i spun it around when i put it back together and it gives more room for table travel in that...
Forum: Machining 03-06-2011, 04:20 PM
Replies: 20
Views: 3,658
Posted By troutback
the more i thought about this, the more i came to...

the more i thought about this, the more i came to the same conclusion.



as you will see below, "missing" isn't the appropriate word.



ok, here ya go.
Forum: Machining 03-03-2011, 10:07 AM
Replies: 20
Views: 3,658
Posted By troutback
part for kurt d-60?

hi folks,
i recently purchased a kurt d-60 milling vise for my little milling machine. upon receipt yesterday, i realized that it was not working properly. there is a dead space between 1 1/2" and...
Forum: Machining 03-25-2010, 06:54 PM
Replies: 29
Views: 9,503
Posted By troutback
thanks for the advice precisionworks. already...

thanks for the advice precisionworks. already replaced it. worthwhile doing the work. if it happens again for some reason, i'll promptly do nothing next time.
Forum: Machining 03-25-2010, 12:21 PM
Replies: 374
Views: 42,811
Posted By troutback
back again, tried the shortcut. it was great...

back again,
tried the shortcut. it was great until i tried to put the spindle back. could'nt seat the top bearings in there like that. not enough room or threads to do it that way. so i had to drop...
Forum: Machining 03-25-2010, 08:01 AM
Replies: 29
Views: 9,503
Posted By troutback
thanks to you both. digr, i've got the...

thanks to you both.

digr, i've got the manual on the computer now. and it'll help although i think the one platypus is gonna send will be better and more detailed. but i appreciate the work you...
Forum: Machining 03-25-2010, 07:59 AM
Replies: 374
Views: 42,811
Posted By troutback
hi cutter, been following your thread as it is...

hi cutter,
been following your thread as it is right along where i'm at with mine. david lee has a point. i did use the machine after the pin sheared off. seem to work fine. but....the old saying,...
Forum: Machining 03-24-2010, 05:46 PM
Replies: 29
Views: 9,503
Posted By troutback
wow, thanks cutter. that's what i needed to see. ...

wow, thanks cutter. that's what i needed to see.

after checking that out, i'm wondering if i could get to that set screw with only half that work. it seems that i could possibly force the shaft...
Forum: Machining 03-24-2010, 04:50 PM
Replies: 29
Views: 9,503
Posted By troutback
that would be great platypus. i'll pay for copies...

that would be great platypus. i'll pay for copies and shipping.

so, if anyone else is reading this, i ran into another problem today. i was giving it a test run by milling some aircraft aluminum...
Forum: Machining 03-24-2010, 09:52 AM
Replies: 29
Views: 9,503
Posted By troutback
guess i was writing when you responded...

guess i was writing when you responded precisionworks.

thanks.
Forum: Machining 03-24-2010, 09:51 AM
Replies: 29
Views: 9,503
Posted By troutback
ok, after thinking a bit harder, it came to me. i...

ok, after thinking a bit harder, it came to me. i figured it out. what an ingenious way of attaching things. still need help with documentation if anyone knows. really appreciate the help. here's a...
Forum: Machining 03-24-2010, 09:03 AM
Replies: 29
Views: 9,503
Posted By troutback
help w/ new central machinery mill/drill 981

i see i am not the only one with a new mill/drill. but my knowledge of such machines is limited to what i could gleen off the internet thingee.

i previously got a bunch of help from some of you...
Forum: Machining 02-10-2009, 10:21 AM
Replies: 12
Views: 5,128
Posted By troutback
thanks for all the advice everybody. ok,...

thanks for all the advice everybody.

ok, now when you mention not running it at more than 100 sfpm, i'm going to assume that is surface feet per minute.

i'm not familiar with that term. how...
Forum: Machining 02-09-2009, 09:26 PM
Replies: 12
Views: 5,128
Posted By troutback
thanks precision works for the info. i guess...

thanks precision works for the info.

i guess i should've clarified my last question.

in a small lathe(i guess mine would qualify) if i can run an end mill bit in it, should i be sticking to a...
Forum: Machining 02-09-2009, 08:05 PM
Replies: 12
Views: 5,128
Posted By troutback
logan 10" powr-kraft(monkey ward)

hi all,
just got a logan 10" x 30. have been wanting a metal lathe for years for an assortment of different projects. none of them engine or car related.

i have been actively trying to find one...
Showing results 1 to 19 of 19

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 05:32 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.