Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 7433
Search took 1.61 seconds.
Search: Posts Made By: milomilo
Forum: Machining Today, 02:52 PM
Replies: 18
Views: 546
Posted By milomilo
Exactly my plan. So far the parts guy says Timken...

Exactly my plan. So far the parts guy says Timken does not stock the number and there is no new P/N for the two inside seals.:( He has a couple more places to contact yet. It may be that I will have...
Forum: Machining Today, 10:26 AM
Replies: 18
Views: 546
Posted By milomilo
Thanks.

Thanks.
Forum: Welding Yesterday, 08:22 PM
Replies: 4
Views: 149
Posted By milomilo
Nice work Ted.

Nice work Ted.
Forum: Machining Yesterday, 05:11 PM
Replies: 18
Views: 546
Posted By milomilo
Pics of the spindle and two bad seals.

Pics of the spindle and two bad seals.
Forum: Machining Yesterday, 03:59 PM
Replies: 18
Views: 546
Posted By milomilo
Took the two inboard seals that were leaking down...

Took the two inboard seals that were leaking down to my local parts house and after measuring he came up with two Timken P/N's. Neither one is listed as current. He is calling Timken today and will...
Forum: Machining Yesterday, 11:54 AM
Replies: 18
Views: 546
Posted By milomilo
I read a thread yesterday about using grease. I...

I read a thread yesterday about using grease. I liked the idea, as there would be no leaks of oil. I am going out to the shop to see if it is feasible. I can do that before I put in the parts so the...
Forum: Machining 10-20-2019, 09:28 PM
Replies: 18
Views: 546
Posted By milomilo
Oil bath. Lathe manufacturer is from Taiwan and...

Oil bath. Lathe manufacturer is from Taiwan and sold out. Manual says zero clearance.
Forum: Machining 10-20-2019, 07:27 PM
Replies: 18
Views: 546
Posted By milomilo
Yes it is.

Yes it is.
Forum: Machining 10-20-2019, 11:02 AM
Replies: 18
Views: 546
Posted By milomilo
What is the correct spindle bearing clearance for...

What is the correct spindle bearing clearance for my 10" lathe?
Forum: Machining 10-19-2019, 03:42 PM
Replies: 18
Views: 546
Posted By milomilo
Piss Poor Timing

Here it is almost winter and I was doing a little fab on an adapter for the newly designed chimney for the wood stove in the shop and the belts on the lathe were once again slipping.

I had...
Forum: Shop & Safety 10-19-2019, 05:47 AM
Replies: 7
Views: 224
Posted By milomilo
Wire brush the broken concrete, wet the brushed...

Wire brush the broken concrete, wet the brushed area and mix up 3 parts sand and one part Portland cement, then add water to a fairly dry mix. apply by hand and shape accordingly. Use a damp paint...
Forum: Fabrication 10-18-2019, 08:21 AM
Replies: 7
Views: 415
Posted By milomilo
Put in a concrete pile about 3' deep and 2'...

Put in a concrete pile about 3' deep and 2' diameter outside with a mount for the bender for those bigger jobs. Move the bender back in when not in use.
Forum: Shop & Safety 10-16-2019, 10:11 PM
Replies: 751
Views: 24,067
Posted By milomilo
Are the trees to far gone to spray?

Are the trees to far gone to spray?
Forum: Fabrication 10-15-2019, 12:47 PM
Replies: 41
Views: 2,558
Posted By milomilo
I have watched several of his videos this last...

I have watched several of his videos this last year. He is a worker for sure.
Forum: Fabrication 10-11-2019, 09:35 PM
Replies: 41
Views: 2,558
Posted By milomilo
Can you use any grease on the nylon bushing?

Can you use any grease on the nylon bushing?
Forum: Mechanical & Electrical 10-10-2019, 09:28 PM
Replies: 19
Views: 1,238
Posted By milomilo
Looks very well done.:)

Looks very well done.:)
Forum: Fabrication 10-10-2019, 09:21 PM
Replies: 13
Views: 696
Posted By milomilo
Maybe something like this...

Maybe something like this (https://www.toolplanet.com/product/Shop-Fox-Cam-Clamps-for-TTracks-Each-D3347/clamps). Pretty simple to make.
Forum: Fabrication 10-09-2019, 09:04 PM
Replies: 24
Views: 1,348
Posted By milomilo
Must be starting to get socialized.:devil:

Must be starting to get socialized.:devil:
Forum: Fabrication 10-09-2019, 08:21 PM
Replies: 41
Views: 2,558
Posted By milomilo
My comment was for a hydraulic operated thumb....

My comment was for a hydraulic operated thumb. However, most fixed thumbs I have seen built did not come out right on the first try either. At least I have never called you an ENGINEER!!!:devil:
Forum: Fabrication 10-09-2019, 07:06 PM
Replies: 13
Views: 696
Posted By milomilo
How much clamping force do you need?

How much clamping force do you need?
Forum: Fabrication 10-09-2019, 11:10 AM
Replies: 13
Views: 696
Posted By milomilo
Looks very nice. Can you add the cam locks now?

Looks very nice. Can you add the cam locks now?
Forum: Welding 10-07-2019, 09:26 PM
Replies: 4
Views: 346
Posted By milomilo
Much fancier than my 2x4 wood frames.:) I just...

Much fancier than my 2x4 wood frames.:) I just used scrap wood from the wood pile.
Forum: Fabrication 10-07-2019, 04:00 PM
Replies: 24
Views: 1,348
Posted By milomilo
My bet is Wednesday 2:00 PM.:devil:

My bet is Wednesday 2:00 PM.:devil:
Forum: Fabrication 10-07-2019, 03:57 PM
Replies: 41
Views: 2,558
Posted By milomilo
Did you get the emails I sent you?

Did you get the emails I sent you?
Forum: Fabrication 10-06-2019, 06:19 PM
Replies: 24
Views: 1,348
Posted By milomilo
Good luck on getting minions to collectively get...

Good luck on getting minions to collectively get 60 hours of work done in 5 days, even presuming you put in five 12 hours shifts.:devil:
Showing results 1 to 25 of 7433

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 09:20 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.