Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 7335
Search took 3.56 seconds.
Search: Posts Made By: milomilo
Forum: Mechanical & Electrical Yesterday, 09:41 PM
Replies: 1
Views: 26
Posted By milomilo
Water Heater Shit The Bed

Went down to the basement for some canning jars after lunch today and found the basement floor a bit moist. After checking the well pressure tank, washer and water heater, determined the water heater...
Forum: Fabrication 08-17-2019, 08:27 PM
Replies: 29
Views: 688
Posted By milomilo
So what are these funnels for?

So what are these funnels for?
Forum: Shop & Safety 08-17-2019, 08:12 PM
Replies: 278
Views: 12,853
Posted By milomilo
Must have melted out the grease in the U joint.

Must have melted out the grease in the U joint.
Forum: Mechanical & Electrical 08-17-2019, 12:15 PM
Replies: 10
Views: 279
Posted By milomilo
What did parts run you for this job?

What did parts run you for this job?
Forum: Fabrication 08-15-2019, 09:39 PM
Replies: 29
Views: 688
Posted By milomilo
I am not much help on the angle question, but I...

I am not much help on the angle question, but I also would start from each end and meet the middle.
Forum: Mechanical & Electrical 08-13-2019, 10:43 AM
Replies: 28
Views: 534
Posted By milomilo
Automotive stores have the fancy digital battery...

Automotive stores have the fancy digital battery testers which are set to the specific battery size for load testing. Usually a free test. That way you can stop guessing about the battery. Burnt...
Forum: Shop & Safety 08-11-2019, 09:49 PM
Replies: 278
Views: 12,853
Posted By milomilo
Was it running on propane for the previous owner?

Was it running on propane for the previous owner?
Forum: Shop & Safety 08-10-2019, 11:17 PM
Replies: 278
Views: 12,853
Posted By milomilo
What Whitetrash says is the way I do it.:)

What Whitetrash says is the way I do it.:)
Forum: Welding 08-08-2019, 11:32 AM
Replies: 7
Views: 745
Posted By milomilo
We need weld pics!!!!!

We need weld pics!!!!!
Forum: Mechanical & Electrical 08-07-2019, 10:33 PM
Replies: 11
Views: 771
Posted By milomilo
Sensor in, truck runs great.:D

Sensor in, truck runs great.:D
Forum: Mechanical & Electrical 08-03-2019, 03:19 PM
Replies: 5
Views: 358
Posted By milomilo
That was fun to watch. Thanks.

That was fun to watch. Thanks.
Forum: Fabrication 07-31-2019, 09:42 PM
Replies: 24
Views: 1,278
Posted By milomilo
Sounds like you have a good new customer.:D

Sounds like you have a good new customer.:D
Forum: Machining 07-31-2019, 08:01 AM
Replies: 7
Views: 411
Posted By milomilo
Get any tooling with it? Nice buy.:p

Get any tooling with it? Nice buy.:p
Forum: Mechanical & Electrical 07-30-2019, 02:47 PM
Replies: 17
Views: 627
Posted By milomilo
For a lift gate, I would run a separate hot wire...

For a lift gate, I would run a separate hot wire to an unused spot of the fuse box. Other than that, I would just tie in to rear existing wiring for the lights.
Forum: Shop & Safety 07-30-2019, 01:35 PM
Replies: 722
Views: 20,156
Posted By milomilo
Hope you roof turns out square. I always square...

Hope you roof turns out square. I always square the roof and sheet it and put on the roofing material before putting on siding. Find it easier to square the walls after the roof.
Forum: Machining 07-29-2019, 09:52 PM
Replies: 6
Views: 425
Posted By milomilo
Ought to last forever IF they keep grease in it.

Ought to last forever IF they keep grease in it.
Forum: Fabrication 07-28-2019, 08:30 PM
Replies: 6
Views: 488
Posted By milomilo
That's a reverse image search. Google's reverse...

That's a reverse image search. Google's reverse image search is a breeze on a desktop computer. Go to images.google.com, click the camera icon (), and either paste in the URL for an image you've seen...
Forum: Mechanical & Electrical 07-28-2019, 01:31 PM
Replies: 11
Views: 771
Posted By milomilo
Bad News/Good News. Bad is the sensor I ordered...

Bad News/Good News. Bad is the sensor I ordered did not come with slotted mounting holes therefore cannot adjust the idle voltage. It is boxed up and ready to return. Good is the new one I ordered...
Forum: Shop & Safety 07-27-2019, 08:00 PM
Replies: 23
Views: 931
Posted By milomilo
Sounds like your life is going to get real busy....

Sounds like your life is going to get real busy. Congrats!!!!!!!
Forum: Fabrication 07-26-2019, 12:21 PM
Replies: 98
Views: 11,549
Posted By milomilo
That trailer ought to last a lifetime. Very nice...

That trailer ought to last a lifetime. Very nice build.
Forum: Blacksmithing & Forming 07-25-2019, 07:13 PM
Replies: 5
Views: 458
Posted By milomilo
And a bit more for the sugar shack.:D

And a bit more for the sugar shack.:D
Forum: Mechanical & Electrical 07-24-2019, 10:24 PM
Replies: 12
Views: 542
Posted By milomilo
That is on my todo list. A nice wood box for me...

That is on my todo list. A nice wood box for me Stihl.
Forum: Mechanical & Electrical 07-24-2019, 08:05 PM
Replies: 12
Views: 542
Posted By milomilo
Mine is stored in a building inside a plastic...

Mine is stored in a building inside a plastic milk crate with a pad to catch any oil. I use mine at least every two months. I do not use ethanol gas and with the 2 cycle oil in the gas, I leave it...
Forum: Machining 07-23-2019, 11:53 PM
Replies: 8
Views: 552
Posted By milomilo
You suck. Very nice score!!!!

You suck. Very nice score!!!!
Forum: Welding 07-23-2019, 09:04 PM
Replies: 13
Views: 639
Posted By milomilo
Old thread on stud welders. Maybe you can contact...

Old thread on stud welders. Maybe you can contact the author via email and see if he can help. He has been on the forum since 2016.

https://www.shopfloortalk.com/forums/member.php?u=413
Showing results 1 to 25 of 7335

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 03:23 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.