Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 9691
Search took 0.93 seconds.
Search: Posts Made By: Shade Tree Welder
Forum: Mechanical & Electrical 10-06-2020, 10:59 AM
Replies: 8
Views: 370
Posted By Shade Tree Welder
Either the grease in the gear box or a #2 EP...

Either the grease in the gear box or a #2 EP wheel bearing grease would be fine for that application.
Forum: Mechanical & Electrical 10-06-2020, 08:55 AM
Replies: 8
Views: 370
Posted By Shade Tree Welder
If that is the correct manual, I would recommend...

If that is the correct manual, I would recommend the following.

https://www.mcmaster.com/8670T12/

You will need 2 tubes of grease.

Spur gears so an EP (sulfur containing) is perfectly fine. ...
Forum: Mechanical & Electrical 10-05-2020, 02:06 PM
Replies: 8
Views: 370
Posted By Shade Tree Welder
Worm gear set?

Worm gear set?
Forum: Mechanical & Electrical 10-04-2020, 01:44 PM
Replies: 3
Views: 328
Posted By Shade Tree Welder
Sorry did not have time last night and wanted to...

Sorry did not have time last night and wanted to get you an answer quick.

Friction modifiers allow the clutches in a LSD to lock up when the relative speed
between the plates are low enough. So...
Forum: Mechanical & Electrical 10-03-2020, 09:35 PM
Replies: 3
Views: 328
Posted By Shade Tree Welder
No. No. No. Those are for limited slip...

No. No. No.

Those are for limited slip differentials.
Forum: Mechanical & Electrical 09-30-2020, 09:33 PM
Replies: 7
Views: 581
Posted By Shade Tree Welder
You suck.

You suck.
Forum: Machining 09-25-2020, 07:13 AM
Replies: 22
Views: 1,881
Posted By Shade Tree Welder
Did he include ammo too?

Did he include ammo too?
Forum: Fabrication 09-05-2020, 04:33 PM
Replies: 44
Views: 2,726
Posted By Shade Tree Welder
Or you can buy a tractor with a loader... :cool:

Or you can buy a tractor with a loader... :cool:
Forum: Fabrication 09-02-2020, 09:31 AM
Replies: 23
Views: 2,005
Posted By Shade Tree Welder
I have been really happy with these. I have not...

I have been really happy with these. I have not used a C-clamp in a few decades.

https://www.bessey.de/en-US/BESSEY-Tools-North-America/Products/Clamping-Tools/Traditional-all-steel-bar-clamps
Forum: Fabrication 09-02-2020, 09:28 AM
Replies: 23
Views: 2,005
Posted By Shade Tree Welder
Mobil Vactra 4. Also Bar and Chain oil in a...

Mobil Vactra 4.

Also Bar and Chain oil in a pinch.
Forum: Mechanical & Electrical 09-01-2020, 11:46 AM
Replies: 7
Views: 381
Posted By Shade Tree Welder
I was mad when I saw the title and I didn't get...

I was mad when I saw the title and I didn't get an invite, but it wasn't what I thought it was... don't do that...
Forum: Blacksmithing & Forming 08-23-2020, 10:21 PM
Replies: 24
Views: 3,512
Posted By Shade Tree Welder
This project got shelved for now... :rolleyes:

This project got shelved for now... :rolleyes:
Forum: Shop & Safety 08-17-2020, 08:48 AM
Replies: 109
Views: 9,497
Posted By Shade Tree Welder
I traded out my old fluorescent bulbs for LED's...

I traded out my old fluorescent bulbs for LED's Huge difference!! And they use
less power and produce more light. They also come on full bright in the cold,
no warm up. And should last decades.
Forum: Mechanical & Electrical 08-14-2020, 03:35 PM
Replies: 5
Views: 358
Posted By Shade Tree Welder
Procon pump maybe. Guessing.

Procon pump maybe. Guessing.
Forum: Mechanical & Electrical 08-05-2020, 08:28 PM
Replies: 16
Views: 874
Posted By Shade Tree Welder
You mean a pressure switch, not regulator. ...

You mean a pressure switch, not regulator.

And I agree with Digr, not likely a good idea. Your amps are gonna double, assuming your not going with a smaller motor.
Forum: Machining 08-02-2020, 12:44 PM
Replies: 18
Views: 1,070
Posted By Shade Tree Welder
The running OD surface of the wheel should be cut...

The running OD surface of the wheel should be cut flat and concentric with the
shaft the wheel runs on. Crowns are only (and not always) cut on flangeless
wheels. Also you need to include a...
Forum: Machining 07-31-2020, 08:55 AM
Replies: 18
Views: 1,070
Posted By Shade Tree Welder
Do you have flanged band wheels?

Do you have flanged band wheels?
Forum: Mechanical & Electrical 07-28-2020, 06:08 PM
Replies: 7
Views: 424
Posted By Shade Tree Welder
Fill it up with the highest octane fuel you can...

Fill it up with the highest octane fuel you can find, and run it like normal.
That is your best option. Run it down low again and refill as normal.
Forum: Machining 07-24-2020, 09:31 PM
Replies: 40
Views: 2,374
Posted By Shade Tree Welder
I think it was a fly cutter a few decades ago... ...

I think it was a fly cutter a few decades ago... now it is just scrap...
Forum: Fabrication 07-24-2020, 09:26 PM
Replies: 25
Views: 3,076
Posted By Shade Tree Welder
Looks like an assembly press to me. Some guy...

Looks like an assembly press to me. Some guy gets to stand in front of it
8 hours a day pressing part A into hole B.
Forum: Mechanical & Electrical 07-24-2020, 06:53 AM
Replies: 34
Views: 1,551
Posted By Shade Tree Welder
Amen, brother, amen! A wider blade will...

Amen, brother, amen!


A wider blade will help with that. you might or might not get one to fit your
machine, most likely not.
Forum: Mechanical & Electrical 07-23-2020, 08:55 PM
Replies: 19
Views: 1,277
Posted By Shade Tree Welder
Is the engine stuck? Does the axle turn? Do...

Is the engine stuck?
Does the axle turn?
Do the tiller blades turn?
How badly worn are the blades?
Gas tank condition?

$25-50, C-note is high.


Most likely...
Forum: Mechanical & Electrical 07-22-2020, 08:51 PM
Replies: 34
Views: 1,551
Posted By Shade Tree Welder
Be careful what you ask for...

Be careful what you ask for...
Forum: Mechanical & Electrical 07-22-2020, 04:02 PM
Replies: 34
Views: 1,551
Posted By Shade Tree Welder
Oh and it is well known here on SFT that I hate...

Oh and it is well known here on SFT that I hate WD-40. Shitty product, great marketing.

WD-40 and a lot of products like it use large doses of silicon in their formulations.
Silicone will fuck...
Forum: Mechanical & Electrical 07-22-2020, 03:57 PM
Replies: 34
Views: 1,551
Posted By Shade Tree Welder
So was I, in the 3/4" blade I think the coarsest...

So was I, in the 3/4" blade I think the coarsest pitch I could get was a 4/6 vari-
tooth, and that was spotty at best. We have the same saw, Ellis 1600, I can
get a 2/3 vari-tooth. Don't use it...
Showing results 1 to 25 of 9691

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 02:57 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.